Mopar Front Splash Guard Pair Sport/Sahara Jeep Wrangler JL 2018-2019/Gladiator 2020

Mopar:
82215332AB
Rating:
95% of 100

Highlights

  • Fits 2 Or 4 Door JL Wranglers
  • Protects The Rocker Pan
  • Textured Black Finish
  • Molded Plastic Construction
MSRP $58.00
$52.99
You save 9%

Pair of Mopar Front Splash Guards for 2018-2019 Jeep JL Wranglers and 2020 Jeep Gladiators.

Add an extra layer of protection to block water, mud, snow, and rocks from flying up and hitting your 2018-2019 Sport or Sahara Jeep JL Wrangler or 2020 Jeep JT Gladiator with this Pair of Mopar Front Splash Guards from CJ Pony Parts!

Mopar Front Splash Guards 82215332AB Features and Benefits:
- Completes front driver and passenger sides
- Molded Design
- Tough and durable
- Protects your JL/JT's undercarriage
- Adds custom styling to your rig
- Can be painted
- Easy installation

These molded Front Splash Guards from Mopar will complete the front driver and passenger side of your 2018-2019 JL Wrangler Sahara or Sport or your 2020 JT Gladiator. They are tested to all corporate standards to ensure that they have the durability to stand up to the everyday rigors of driving. This pair of splash guards not only protect the lower body of your JL/JT, but they also add a great custom style with a black finish that can be painted to match your Jeep!

Please Note: These splash guards will NOT fit Jeep JL Wranglers that are equipped with rock rails. They will NOT fit Rubicon model Jeep Wranglers due to the factory-installed rock rails and rear steel bumper.

CJ Pony Parts carries a wide assortment of Jeep parts and Jeep accessories designed specifically for your JL. From lighting and suspension to exhaust and other accessories, CJ's has what you need to easily upgrade your Wrangler.

Order this Pair of Mopar 82215332AB Front Splash Guards for your 2018 or 2019 Sahara or Sport Jeep JL Wrangler or 2020 Jeep JT Gladiator from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

We just added some more protection to our JL. We're going to show you how to get it done.

When you take your Jeep out on the trail, you pick up rocks and stones and they can be thrown out of your tires when you get back onto the highway. This can cause damage to your own vehicle as well as many others, so today we're going to prevent that by installing a set of these Mopar Front Splash Guards, fitting your new 2018 Jeep JL Wrangler.

These Mopar Front Splash Guards feature a durable construction with a black finish to match your exterior fender flares. They include all the rivets to get them installed, plus it's going to provide a ton more protection to your Jeep Wrangler. With that being said, let's get them installed on our 2018 Jeep JL.

Tools needed for this installation, a pair of snips, trim removal tool, a drill, quarter-inch drill bit and a rivet installation tool.

We're at the front driver's side of our Jeep and we do have the wheel entirely removed just to make it a little bit easier for you guys to see what we're doing. We're going to start by removing a few of these clips here on the front fender, and get started with the install.

In order to install the new splash guards, you have to remove these two rivets and then two push pins on the inside. These two rivets have to be cut off, and then the push pins can be pulled out by a trim removal tool. Next step is the two push pins. Use a trim removal tool, get under them.

Go ahead and grab your driver's side splash guard. This side is going to be labeled as a left hand. This nice finished edge is going to face in towards the fender flare. Let's get it installed.

The two rivets that you removed on the outside, and then these two push pin holes are where the new rivets are going to be installed. Simply line it up like so, grab one of your rivets, and put it through the hole there. Grab your rivet gun. This is definitely a great tool to have, if you're going to be doing more modifications. Slide the rivet into the tip, give it a good squeeze. Just like that it's installed, and cut, ready to go.

One of the nicest parts about these tools are you can actually borrow them at a local hardware store, or an automotive store. Pretty cool tip, and if you don't have one, it makes this install a lot cheaper. Once you have all four of these installed, it actually lines it up really nice, and you can drill the hole for this fifth hole here. It's going to go through the splash guard, through the inner fender liner, and then you can install a rivet. Use a quarter-inch drill bit. It should be nice and simple. It's just thin plastic. Now you're ready to put the rivet on.

With that last rivet installed, you can now repeat the same process on the other side, and your installation is complete. We just finished up the install of the Mopar Splash Guards on the front end of our JL. They look really awesome, and it only took about 30 minutes to install. This is going to prevent debris from flying up on your tire and hitting your Jeep or people behind you.

Now you can find these splash guards as well as many other great parts for your JL right here at CJPonyParts.com.

Vehicle Fitment

This product will fit the following Gladiator years:

  • 2020

This product will fit the following Wrangler years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.