Rear-End Lowering Kit 1" 1967-1970

CJ's Part Number:
CLK1042
Rear-End Lowering Kit 1" 1967-1970 is rated 4.9 out of 5 by 7.
  • y_2019, m_10, d_15, h_7
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.13
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_7
  • loc_en_US, sid_CLK1042, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getAggregateRating, 130.21ms
  • REVIEWS, PRODUCT

Highlights

  • Lower Rear By Approx. 1"
  • Compatible W/Stock Leaf Spring
  • Quick And Easy Installation
  • Sold As A Complete Kit
MSRP $48.95
$42.75
You save 13%

1-Inch Rear-End Lowering Kit for all 1967, 1968, 1969 and 1970 Mustangs.

The most commonly performed suspension mod on a Mustang is lowering it to give it a more intimidating, aggressive look. Lowering the rear-suspension of your classic, 1967-1970 Mustang doesn’t have to be expensive or difficult. You can easily lower the rear-end of your pony car yourself, DIY-style with this 1-Inch Rear-End Lowering Kit for your 1967-1970 Mustang from CJ Pony Parts. Skip the pricey mechanic and order your own kit today!

Kit Includes:
- (2) Die-cast aluminum lowering blocks
- (4) U-Bolts
- (8)-Piece set of nyloc nuts

Features and Benefits:
- Lowers the rear-end by approx. 1”
- Lowering blocks made from die-cast billet aluminum
- Useable with stock leaf springs
- Works for all 1967-1970 Mustangs
- Inexpensive DIY
- Sold as a complete kit for your convenience
- Direct-fit replacements, easy installation
- Instructions provided

This inexpensive, do-it-yourself kit works to lower the rear-end of your 1967-1970 Mustang by approximately 1 inch. This convenient, 1-inch rear-end lowering kit includes (2) die-cast, billet aluminum lowering blocks; (4) U-Bolts and an 8-piece set of nyloc nuts. When installing this kit, you can use the stock leaf springs, which came factory with your classic pony car. These direct-fit replacement pieces are easily installed on any 1967-1970 Mustang and include comprehensive, easy-to-follow installation instructions.

The suspension in your 1967-1970 Mustang has an important job to perform. Vehicle suspension engineering and design has come a long way since 1967-1970. Therefore, there are plenty of great options available for upgrading your old and worn out suspension. If you’re looking to simply tighten up or repair your suspension, a few easy bolt-on options will add up to create an overall suspension improvement.

Order a 1-Inch Rear-End Lowering Kit for your 1967, 1968, 1969 or 1970 Mustang from CJ Pony Parts today!

Installation Difficulty

Easy
Easy

Novice skill is required for this installation.

Installation Videos

Vehicle Fitment

This product will fit the following Mustang years:

Rated 5 out of 5 by from Fit great, happy! Had to order these after returning the 65-66 kit as I have 64 Ranchero that has had the rear end swapped out when converting to a 8 cylinder drivetrain where the rear end apparently came out of a 66+ vehicle as the rear end does not taper to smaller on the ends. The 65/66 are slightly narrower, so be sure you are getting the correct kit. Aside from that, fits great, dropped the rear end down a bit as desired!
Date published: 2017-06-22
Rated 4 out of 5 by from Great kit, maybe fitment issue Installed this today on my 1970 Mach 1. Nipple on leaf spring was too big to fit into the block that cj sent, so had to enlarge hole in lowering block with drill bit to allow leaf spring nipple to fit into block. About a 3 hour install from start to finish.
Date published: 2018-06-08
Rated 5 out of 5 by from Fits like a charm! Installation took about 40mins. Basic tools and common sense goes a long way. Rear lowered 1" and u-bolts long enough to install a 2" block(must buy seperately).
Date published: 2016-02-02
Rated 5 out of 5 by from simple and easy Easily one of the simplest mods I done it only took about 40 minutes to put on and the cars sits perfect now
Date published: 2015-01-08
Rated 5 out of 5 by from Fit as advertised Haven’t finished car yet to know how much it actually lowered but fit good and looks good
Date published: 2018-06-26
Rated 5 out of 5 by from Fit great Good price, quality material, easy installation.the car looks nice as well.
Date published: 2017-05-18
Rated 5 out of 5 by from Good product Lowering kit install is easy and works as advertised. Good value.
Date published: 2018-05-13
  • y_2019, m_10, d_15, h_7
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.13
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_7
  • loc_en_US, sid_CLK1042, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getReviews, 3.67ms
  • REVIEWS, PRODUCT

Do this lowering blocks fit the ford 9 inch rear axel?

Asked by: Sven
Yes, this will fit.
Answered by: CJPP Dave
Date published: 2015-11-22

Will these parts work on a Ford Maverick?

Asked by: Takamine
It's possible. However, unless the Maverick is listed as an alternative fitment on a part, we can't say for sure whether it will or won't work, since neither us nor the manufacturer have tested it.
Answered by: CJ Pony Parts
Date published: 2015-03-30
  • y_2019, m_10, d_15, h_7CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.13
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_2
  • loc_en_US, sid_CLK1042, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 101.72ms
  • QUESTIONS, PRODUCT
Complete Your Package
Add to Cart