RetroSound Products Long Beach Radio With Black Face/Buttons And Chrome Bezel/Knobs 1965-1966

RetroSound Products: RSRD44
MSRP: $419.99
CJ's Low Price:
$349.99
1508716800 68676
Add these other great RetroSound Products parts to your order for your new Long Beach radio!
Earn 349 RPM Points What's this?
RetroSound Products Long Beach Radio With Black Face/Buttons And Chrome Bezel/Knobs 1965-1966
RetroSound Products Long Beach Radio With Black Face/Buttons And Chrome Bezel/Knobs 1965-1966 RetroSound Products Long Beach Radio With Black Face/Buttons And Chrome Bezel/Knobs 1965-1966 Play RetroSound Products Long Beach Radio With Black Face/Buttons And Chrome Bezel/Knobs 1965-1966 Video 1
RetroSound Products

Product Description

RetroSound Products Long Beach Radio with a Black Face and Buttons and Chrome Bezel and Knobs for all 1965-1966 Mustangs.

The RetroSound Products Long Beach Radio with a Black Face and Buttons and Chrome Bezel and Knobs from CJ Parts will keep the vintage look and feel of your classic 1965-1966 Mustang while offering modern features. Such as built-in Bluetooth connectivity, iPod and iPhone usability, 32,000 color display, and many other features.

RetroSound Products Long Beach Radio RSRD44 Features and Benefits:
- Black Face and Buttons with Chrome Bezel and Knobs
- Made for iPod and iPhone
- SiriusXM Ready
- Built-In Bluetooth Connectivity
- 32,000 Color Display for Personal Customization
- Authentic Push-Button Styling
- Two Rear-Mounted USB Ports for iPod/iPhone or USB Flash Drive
- Two Auxiliary Inputs
- AM/FM RDS Tuner with 30 Pre-Sets
- Built-In 25 Watts x 4 Channel RMS Power Amplifier
- Dual RCA Pre-Outs and Subwoofer Output for External Amplifiers
- Works Seamlessly with RetroSound External Amplifiers
- Easy to Install with RetroSound's Patented InfiniMount Adjustable Bracket System
- Can Remotely Mount Body Using Optional Extension Cable for Custom Installation

The Long Beach radio from RetroSound Products is the only Made-For-iPod/iPhone radio available for the classic 1965-1966 Mustang. It is the most technologically advanced radio available that will retain your Mustangs classic look with its vintage radio styling. This Long Beach radio has Bluetooth connectivity for hands-free calls or wireless audio streaming and comes SiriusXM ready. You can connect to SiriusXM with the SiriusXM SXV300 Connect Vehicle Tuner (sold separately, CJ’s part number SXV300V1). A 32,000 color display will allow you to customize the radio's display to match your Mustangs interior.

In the rear of the radio are two USB ports and two standard auxiliary inputs for use with your mobile devices. The Long Beach radio comes with a built-in 25 watt x 4 channel power RMS MOSFET amplifier, however, if you would like to add your own, there are front and rear RCA pre-outs as well as a subwoofer output to really bring the noise! Installation of the radio is easy, as it will mount seamlessly into the dash of your Mustang with RetroSound’s patented InfiniMount Adjustable bracket system.

Long Beach radio Specifications:

FM
Tuning Range (USA, EUR, AUS, JAP, RUS tuning capable) with RDS: 87.5-107.9MHz
Antenna Terminal: External Antenna Connector
Usable Sensitivity: 12.5 dBf
Selectivity: 75 dB @ 400kHz
Signal to Noise Ratio: 62 dB (Stereo), 67 dB (mono)
Harmonic Distortion @ 1 kHz: 0.8% (stereo), 0.5% (mono)
Separation: 32 dB @ 1kHz
Frequency Response: 30-16,000 Hz

AM (EU and US Tuning Capable)
Tuning Range (USA, EUR, AUS, JAP, RUS tuning capable): 530-1710 kHz
Antenna Terminal: External Antenna Connector

General
Dimensions (radio face & push-buttons only): 3.5²W x 1.5² H x 1.05² D
Dimensions (radio body): 3.96²W x 1.98²H x 4.30²D
Power Requirements: 10.5-14.4 volts
Current Consumption (during operation): Max. 15A
Current Consumption (car off): <3.5 mA
Output Power (@ 14.4 volts @ 4 ohm @ 1% THD): 25x4 watts RMS 45x4 watts Max Power
Output Impedance: 4
Low Level Output (4 channels): 2.85 volts
AUX 1 Input: >300 mV / 6 k‡
AUX 2 Input: >300 mV / 6 k‡
USB 1 Input: 5V (USB female input)
USB 2 Input: 5V (USB female input)

The radio in many early and late model Mustangs wasn't great. Mustang owners shouldn't have to be stuck with an AM single speaker radio, though, as CJ Pony Parts offers many high-quality, retro-looking replacement Mustang radios. These radios feature that retro look with modern conveniences, like iPod/MP3 connectivity and Bluetooth!

Order this RetroSound Products RSRD44 Long Beach Radio with a Black Face and Buttons and Chrome Bezel and Knobs for your 1965-1966 Mustang from CJ Pony Parts today!

Similar Mustang Parts

similar Mustang parts More Mustang Parts  

Installation Instructions

Mustang Installation

Mustang Applications

This product will fit the following Mustang years:

Product Reviews

Write a review
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 115.53ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

Product Questions

Do these radios work with Android phones?

Asked by: AlMcD
No it will not.
Answered by: rk cjpp
Date published: 2017-09-12
  • y_2017, m_10, d_21, h_20CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_1
  • loc_en_US, sid_RSRD44, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 34.64ms
  • QUESTIONS, PRODUCT

You Might Also Like

Product Video

RetroSound Products Long Beach Radio With Black Face/Buttons And Chrome Bezel/Knobs 1965-1966 Video Transcript
By Bill Tumas: We have Lucy, our 1965 Mustang convertible back here in the studio today. Now if you remember when we introduced this car to you a little while back, our goal with Lucy was to build a nice fun convertible driver. In my opinion, for a quality driver to really be enjoyable, you have to have a good stereo. The stereo in this car is an older style vintage radio that simply is not cutting with modern technology, but thanks to RetroSound in Long Beach, we can have all the modern amenities in our 1965 Mustang convertible.

Now we're putting in RetroSound radios here because of the modular capabilities. It give you all kinds of options. The Long Beach 4 shown here is available with a bunch of different faces, different knobs, different finishes. It's also available for different years as far as the overall fitment goes. If you notice, the display and the radio are actually two separate pieces right now. We're going to actually assemble them later. One of the things with the Long Beach, though, is you don't have to mount the body in the dash. You can actually mount this remotely, get an extension cable available here at CJ's, and have the display and the radio mounted separately.

As far as radio features go, this thing is absolutely loaded up. It's designed to work with your iPod or iPhone, it features Bluetooth capability, it is Sirius XM ready, it's a fully customizable display. You've got two USB inputs, two auxiliary inputs, and then front, rear and subwoofer outputs, along with a built-in 25x4 amplifier. Again, all the features that you would find in a modern radio.

For this installation, we need a 3/8 ratchet, half-inch socket, Philips head screwdriver, and basic wiring tools.

The first step of the installation is under the hood. We're going to disconnect the battery. I'm going to run you through the process of how to install the radio. RK's going to handle the actual wrenching for me.

We're going to start by removing our console. I'm not going to say this is necessary, because it actually isn't. You can work around the glove box and behind it, but you'll never be able to see what we're doing, plus it makes it a lot easier. Don't worry if you're worried about how to restore the console. We're actually going to do a future video on how to remove it, rebuild it and put it back in the car. So we're just going to get it out of the way for now and begin our radio installation.

Now we're going to remove the ashtray and then the bracket above it to give us a little more access to the radio. Our car already has an aftermarket radio. It's an older style radio, but it does work, so we know the wires and stuff going to it should be okay. What we're going to do now, though, is start fishing the wires through the back of the car here underneath the dash and make sure the wiring collars are good, and then figure out the wires we need to hook up our new RetroSound radio.

This is pretty much typical of what you're going to find if an aftermarket radio has been installed. There's usually a big pile of wires stuffed up underneath the dash somewhere. Basically what you want to do now is look at the colors so we can figure out the wires we're going to need for our new install.

Something else I want to mention too, don't assume the previous radio was installed correctly. As you can see by the wire nuts, whoever installed this obviously really didn't know what they were doing and didn't do the correct connections. Make sure the colors are correct. Make sure everything works properly before installing the new radio.

All right, the wires are disconnected, now we can remove the radio, and to do this basically you're going to remove the knobs from the front, and in theory it's going to be bolted on. You also want to check the back. There may be a back strap holding up to support it. In our case, we can tell our radio is fairly loose. We know there's no back strap. So we're just going to remove the nuts from the front and then remove the radio through the back of the dash.

Since we're going to mount the body of the radio with the faceplate, the first thing to do is to connect the two of them together. We're going to plug it in. We use the supplied hardware. We screw it on the sides to keep it in place.

Now the radio's obviously going to have a digital display, but if you really want to keep the vintage look when the radio is off, RetroSound provides these screen protectors that look like an old school analog radio. You can put it over the screen. That'll give it more of a vintage look when it's not turned on. Now with the faceplate mounted, we're going to install the brackets for the InfiniMount. These are going to bolt to the sides of the radio, and then actual stalks for the controls will go through the front, allowing you infinite adjustment to get it centered in the dash properly.

All right, now we're going to assemble the control stalks and put them on the InfiniMount. What you want to do is put a nut and washer on it and slide it through the opening, and then do the same on the front. Then repeat the process on the other side and plug them into the sides of the radio. Finally with the system you will have to make some adjustments to get it to line up properly. What we found is you can either use ... line it up with the old radio you removed or use the faceplate that's included by RetroSound, use that to line up the stalks and brackets to get it straight before it goes in the dash.

Keep in mind when adjusting the control stalks, to get them in the right location you can also modify the depth of how far the stalk actually fits out of the dash. That's more of a personal preference, but make sure they stick out for enough for the knobs to fit. We've found that by leaving a little gap around a quarter inch behind the plate, it's pretty much perfect for your 1964 through 1966 Mustang. While these radios are nice and lightweight, the nuts going through the dash are not recommended to be the only thing supporting the radio. It includes a nut and a back strap to install, which provides additional support and make the radio much more firm when it's mounted. Now you can reinstall the faceplate once everything is set up, and the radio's ready to go in the car.

What we're going to do now is actually do all the wiring connections inside the car. What's nice is the harnesses disconnect, so we can connect to our speaker wires and connect the power harness, then put the radio in and simply plug it in. A little trick here, while you're hooking up your speaker wires, if you're not sure which speaker goes to where, grab a small battery ... don't use a drill battery ... but grab like a nine volt or a small D or C cell battery. Touch the terminals together and the speaker will pop. That'll tell you which speaker the wire goes to.

With the harness all wired up, now we're going to install the harness on the back of the radio itself. We're going to put the radio up into place and mount it just with the dash bolts for now. Then we'll plug everything in and work on the back strap. Just be careful when you fish the stereo up. This will obviously be a lot easier than the one we took out. You just want to make sure you don't grab any wire or get stuck on anything. And then mount and install a washer on each side and then two more nuts.

With the radio mounted, we're going to plug it in. Once you plug everything in, this is a good time to reconnect your battery, turn the radio on, just make sure it works before we move further with hiding the wires and finishing the installation. Now we're working on seeing where everything's going to fit, getting some of the wires up tucked out of the way, and then mounting the back strap.

With the radio mounted now and all the wires connected, the last step in the radio installation is to install the knobs. Now you want to reinstall any dash components you removed, reconnect your battery, and your installation's finished.

With the radio installed, we're going to run you through some of the basics of how to operate it. To turn the radio on, simply press this button on. You get the RetroSound logo will pop up on the screen, and it will return to the last thing you listened to, which in our case was the radio. We have Bluetooth connected because I have my phone actually on Bluetooth. Now if you want to change sources, that'll give us satellite radio, auxiliary 1, auxiliary 2, and then it'll go to Bluetooth. Then Bluetooth will automatically start playing, and it's going to show you the name of the album, the name of the artist, and the name of the song as well.

You notice the colors are constantly changing. You can pick a color and stay with it, or you can flick through the colors or just have it go like this where it's constantly changing, which I think gives it a nice custom look. If you want to change the sound, you hit this here, and you have some presets. You can turn off the processor, and you go pop, rock, classic, or off, then you flick through it here and you get your bass, midrange, treble, and your balance or fader, extra bass if you want that turned on. This is where your subwoofer control would be. You can turn the sub on if you have one hooked up and have adjustment of it there. And if you leave it go, it will go back to the normal setting in a minute.

I should mention the USB sources. It does have two USBs, as we showed you earlier. The USBs will only work if something's plugged in. So once you plug something into the USB plugs, you'll get that as an option when you're going through sources. You have over here, you go through next track, previous track, replay one/all. You get different features over there.

While you're connected to your phone or using your iPod, you can actually go in here too, you can click to the left and it will bring up the different playlists you have saved in there, so you actually can scroll through those ... again, this will work on Bluetooth or USB ... and pick whatever songs you want to listen to. We'll flip back to radio. When you get a radio station you like, simply hold this down and it will make it a preset. You've got FM1 and FM2, so you're going to have 12 presets there, then more AM presets as well. When you're all finished, you just shut the car off or hold this down and turn it off.

The RetroSound Long Beach radio was the perfect upgrade for our 1965 Mustang convertible. It gives us all the modern amenities we're looking for in a radio, Bluetooth, USB, cell phone, everything works through this radio. The best part about it though, we don't have to cut the dash, and it keeps a very stock look, which we like. It's got plenty of upgrades available as well, so we're going to add amplifiers and speakers probably in the future, make this car sound a heck of a lot better. As far as the installation goes, it's pretty straightforward. Figure about an hour or two, and you'll be back on the road in no time.