RockJock 60VXR Crate Axle Rear With ARB Air Locker And 4.88 Gears Jeep Wrangler JK 2007-2018

RockJock:
CE-KR6501A48
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getAggregateRating, 128.85ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

Highlights

  • Toughest RockJock 60 Available
  • All Critical Areas Reinforced
  • Heavy Duty Components
  • Integrated Skid Plate
MSRP $7,276.00
$6,912.20
You save $363.80

RockJock 60VXR Rear Crate Axle With ARB Air Locker And 4.88 Gears for 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 and 2018 Jeep JK Wranglers.

Designed for extreme off-road use with up to 40-inch tires and V8 conversion horsepower, the RockJock 60VXR Front Crate Axle (CE-KR6501A48) is the strongest 60 series axle in the lineup. It’s loaded with features including a stronger reinforced Stage 2 radius bottom center section, ring gear load bolt, large 3.5-inch axle tubes, full-floating axles with bigger brakes plus much more. If you seek out the most challenging routes and toughest obstacles to conquer, then the RockJock 60VXR is the crate axle of choice for your JK Jeep Wrangler.

Features and Benefits:
- RockJock Stage 2 center section features 9 lbs. more reinforcement in critical areas
- Smooth radius bottom center section improves obstacle slide-over
- Serviceable skid plate resists damage
- Ring gear load bolt eliminates deflection, to increase torque handling capacity
- Highest ground clearance of any 60 on the market
- 35-spline 4340 chrome moly inner and outer axles
- High volume flow-thru recirculating oil system reduces operating temperatures Load bolt eliminates ring gear deflection, dramatically increasing the ring gear's torque capacity
- Large front pinion bearing to handle the increased load of high pinion geometry
- Strong 3-1/2 inch diameter, .375 wall axle tubes maximize strength and resist trail damage
- Full floating design isolates axles from the stresses of vehicle weight and side loads

Features and Benefits:
- Center Section: Stage-2 high-pinion nodular iron, radius bottom, thicker walls and webbing
- Bearing Caps: Stronger, increased cross section bearing caps with ARP fasteners
- Pinion Bearing: Large diameter front pinion bearing matched to rear bearing
- Pinion Oiling: High volume flow-thru recirculating oil system
- Gear Set: 4.88 Standard Dana 60, compatible with super 60 reverse cut gears. Ring Gear Load Bolt Eliminates ring gear deflection under heavy load (3/4 inch-16 RH thread with Jam nut)
- Locker: ARB Air Locker
- Pinion Yoke: 1350 U-joint
- Skid Plate: AR400 hardened steel skid plate
- Differential Cover: Nodular-iron cover with gasketed fill plug with dipstick, Red
- Axle Tubes: 3.5 inch diameter. .375 wall DOM tubing
- Axles: Currie Performance full floating 35-spline 4340 heat treated chromoly
- Floater Spindle: 2.5 inch 4140 Chromoly spindle, supports 35 or 40-spline axles
- Floater Hub: 35-spline drive flanges, JK tone rings installed for ABS and ESP retention
-
Brake Rotor: 13 inch vented rotors with zinc plated caliper brackets
-
Brake Calipers: New factory JK rear Calipers
-
Suspension Brackets: Heavy gauge 3/16 inch steel mounting brackets with multiple mounting locations that enable the suspension geometry to be tuned
-
Geometry: Optimized for 4 inch lift kits with 5 degrees of pinion angle to reduce driveshaft
-
Width: 70 inch wide, enables increased turning angle with 40 inch tires
-
Wheel Bolt Pattern: 5 on 5-1/2 with 1/2 inch wheel studs

Vehicle Fitment

This product will fit the following Wrangler years:

  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getReviews, 5.52ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 117.03ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;