Roush Cold Air Intake Kit Ford F-150 2.7L/3.5L EcoBoost 2018-2022/ F-150 3.5L PowerBoost V6 2021/ F-150 Raptor 2018-2020

Roush:
422089
Rating:
86% of 100

Highlights

  • Direct Fit Design
  • Complete Cold Air Intake Kit
  • Easy Installation
  • Made in the USA
MSRP $458.99
$382.49
You save 17%

Roush Cold Air Intake Kit for 2018, 2019, 2020, 2021, and 2022 Ford F-150s with a 2.7L or 3.5L EcoBoost Engine, 2021 F-150s with a 3.5L PowerBoost V6, and 2018, 2019, and 2020 F-150 Raptors.

The Roush Performance Cold Air Intake Kit (422089) for 2018-2022 2.7/3.5L EcoBoost F-150s, 2021 PowerBoost F-150s, and 2018-2020 F-150 Raptors feature two important benefits: the latent potential in power and fuel efficiency, and reduced pressure drop. Custom tuning isn’t necessary since this CAI system's been engineered and tested specifically for this application. This kit has increased inlet and airbox sizing to allow for maximum airflow and provides added induction noise for that aggressive performance sound. Roush designed this intake using OEM CAD data to guarantee optimized fitment, keep out heat and encourage maximum performance.

Features and Benefits:
- Improved engine performance with no PCM recalibration required
- Provides added induction noise and aggressive performance sound
- Up to 25% less intake restriction compared to stock
- Increased inlet and airbox sizing to allow for maximum airflow
- CAD designed for enhanced sealing
- High-flow, high-capacity, washable and reusable performance
- Exceptional filtration properties
- Lid includes hydrocarbon trap (Emissions Compliance Device)
- Utilizes EPDM rubber couplers
- Complete system from air inlet to throttle body
- Includes all necessary hardware

The high-flow, high-capacity dry filter is proven to retain its shape and is composed of an inner and outer layer of wire mesh for durability and reliability. This filter is washable and no oiling is required. This kit uses EPDM rubber couplers for the correct fitment under engine load, rocking and twisting, and will not void your factory warranty. Factory mounting locations and necessary hardware are used for quick and simple installation.

Kit Includes:
- Air filter with clamp
- EPDM rubber couplers
- Oversized injection-molded air box tray
- Clean air tube
- 105mm mass airflow tube
- Required mounting hardware

Vehicle Fitment:
- 2018-2020 Raptor
- 2018-2022 F-150 2.7 & 3.5L EcoBoost
- 2021 F-150 3.5L PowerBoost V6

California Residents: Proposition 65 Warning

This item is 50-state legal (CARB E.O. Number D-418-43)

Installation Difficulty

Easy
Easy

Novice skill is required for this installation.

Installation Videos

Video Transcript

Today on CJ Off Road, we're gonna help out 2018 F150 breathe a little better with some help from Roush.

One of the easiest ways to improve the performance and efficiency of your truck, is with a nice cold air intake. So, today we're going to be installing this Roush cold air intake on our 2018 F150. This Roush cold air intake is designed to be an easy direct fit replacement for the factory intake on your EcoBoost F150 and Raptor. It features a high flow polyethylene intake tube with a massive pre-oiled air filter and it's protected by a two piece housing with an inspection window. It reduces intake restrictions by 25% for improved performance and efficiency and the best part is, it won't void your warranty.

Tools you'll need for this installation, seven millimeter socket, eight millimeter socket, 5/16th socket, 10 millimeter socket, T-30 torques bit and extension, quarter inch ratchet, 13 millimeter socket, 3/8th ratchet, a center punch, 17/64th drill bit, a drill and safety glasses.

Okay, installing this intake is pretty simple. The first thing we have to do is obviously remove the factory one. We're going to disconnect these two clips on the air box. We'll loosen up these two hose clamps. Use a seven millimeter socket to get these hose clamps off. This one’s a bit trickier to get to just because it's hidden on the back side. Lift up on the intake to remove it, twist this sensor to remove it and then you can unplug it and this will transferred over to your new Roush intake.

Remove this 13 millimeter bolts that secures the bottom portion of the air box. You can use a pen or removal tool, or a flat head screwdriver to remove this from the air box. Remove the two clips on the front of the air scoop and now the whole assembly can come out.

Okay, we're over on the table now and you want to go to Roush’s website and print out the template for this intake. We're going to cut this out and use this to drill two holes on the air box. Place the template over the air box and use a punch to mark the two holes. Now drill the holes with a 17/64th's drill bit.

Now we're going to mount the bracket that comes with the kit, with the provided bolts. Tighten the bolts with an eight millimeter socket. We're going to separate the factor air scoop from the air box by removing this screw. Then, we're going to transfer the air scoop over to the Roush air box. Secure the scoop to the Roush housing with the factory screw. Remove the sleeve and bushing from the factory air box and install this back on to the truck.

Reinstall the bolt and the bushing into the factory location on the truck. Our Roush intake will attach to it by just sliding over it. You don't need to crank down on it too hard, just make it snug. Install the Roush air box into the truck, reinstall the two clips up front. Reattach this clip to the bracket that you bolted to the air box. Install your filter adapter onto the air filter. Install your filter into the air box and attach it with the provided hardware.

Assemble all the couplers and clamps on to the Y pipe, then install it. Get it all situated and then tighten down all the clamps. Take the extension harness that comes with the kit and plug it into the intake sensor connector. This will allow the sensor to go right here. Install the sensor, twist it to lock it and plug it in.

The final step is, if you want to, you can install the inspection window on top of the air box, or you can leave this off if you want. And it's gets secured with the provided screws. And our installation is finished.

Okay, we got our Roush cold air intake installed on our 2018 F150. It looks a lot better under the hood and it's going to help our truck to breathe a lot better than the factory intake too. To get even more performance out of it, you could remove this inspection window if you want. Install was pretty easy. It shouldn't take you more than an hour and before you know it, you'll be heading off road.

Vehicle Fitment

This product will fit the following F-150 years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.