Rugged Ridge A-Pillar Switch Pod Kit Black With 4 Rocker Switches Driver Side Jeep Wrangler JK 2011-2018
- A-Pillar Rocker Switch Panel
- Includes 4 Rocker Switches
- Pre Molded Cut Outs
- Easy Installation
Rugged Ridge Black Driver Side A-Pillar Switch Pod Kit with 4 Rocker Switches for all 2011, 2012, 2013, 2014, 2015, 2016, 2017 and 2018 Jeep JK Wranglers.
Needing a place to mount accessory switches in your 2011-2018 Jeep Wrangler JK? Well, then you should take a look at this Rugged Ridge Black Driver Side A-Pillar Switch Pod Kit with 4 Rocker Switches from CJ Pony Parts! This pillar switch pod kit is a great and easy way to mount your accessory switches in your JK.
Rugged Ridge A-Pillar Switch Pod Kit 17235.96 Features:
- Textured molded plastic finish matches factory pillar cover
- Pre-molded cutouts for up to four switches
- Four rocker switches included
- Easy Installation
The textured molded plastic finish of this Black Driver Side A-Pillar Switch Pod Kit from Rugged Ridge will fit in with your JK’s interior as it matches the factory pillar cover that it will be replacing. Mounting to the A-pillar of your Jeep will make your accessory switches easy to reach and keeps them out of the way from your shifter handle. This kit will include 4 rocker switches which will fit perfectly into the pre-molded cutouts on the switch pod. The pillar switch pod was designed to be easy to install as it will simply snap into place using the factory metal retainer clips just like your OE pillar cover.
Rugged Ridge manufactures Jeep parts and accessories for the growing Jeep and off-road enthusiast market. Rugged Ridge has designed and crafted thousands of products for the Jeep market and continues to develop hundreds of additional Jeep accessories each year.
Order this Rugged Ridge 17235.96 Black Driver Side A-Pillar Switch Pod Kit with 4 Rocker Switches for your 2011, 2012, 2013, 2014, 2015, 2016, 2017 or 2018 Jeep JK Wrangler from CJ Pony Parts today!
California Residents: Proposition 65 Warning
Novice skill is required for this installation.
This Rugged Ridge A Pillar Switch Pod is a direct fit replacement for the factory A Pillar and includes four 21 amp switches to control your auxiliary lighting. The switches come in four different illuminated colors and the A Pillars come in two colors, black and gray, to match your interior and today, we're going to install it in our 2016 Jeep Wrangler. For this installation, you'll need a very sharp knife or a Dremel, a T20 torque spit and a Phillip's screwdriver.
Before you install the A Pillar switch pod, figure out how many switches you want to install, then cut out a hole for each switch. In our case, we're going to do all four. You can use a hobby knife or a Dremel to do this. Once you get all the holes cut, you can insert the switches and using a Dremel will really make this easier. Now, we won't be doing any wiring with this because we don't have anything to hook it up to, but once you do the wiring, this is what the switches will look like when you illuminate them.
Once inside the vehicle, we'll remove the two T20 torque spits holding on the sun visor. Remove this Phillip's head clip, then you can pop this panel off, unplug this connector, then just pull out the A Pillar. If you were going to do any wiring, I would suggest doing it before you install the A Pillar, but we're not going to be doing any wiring, so we can just install it now. Connect the connector and reinstall the corner piece. Finally, reinstall the sun visor and your installation is finished.
Our Rugged Ridge A Pillar switch pod is installed. It's going to make wiring up lighting a lot easier in the future. Installation is going to take about an hour and before you know it, you'll be heading off road.