Rugged Ridge LED Underbody Rock Light Kit White With Harness/Switch

Rugged Ridge:
MSRP $157.49
You save 14%

Rugged Ridge White LED Underbody Rock Light Kit with a Harness and Switch.

Rugged Ridge's White LED Underbody Rock Light Kit with a Harness and Switch is a complete package to equip your off-road vehicle so that you can see and be seen when piloting the trails after dark. Designed with the off-roader in mind, the LED rock lights utilize waterproof aluminum housings for safe and reliable performance in all weather conditions.

Rugged Ridge White LED Underbody Rock Light Kit (11232.40) Includes:
- Four white LED rock lights
- Weather-resistant connectors
- Four flat mounts
- Four curved mounts
- Switch
- Relay
- Wiring
- Hardware

The kit includes four flat mounts and four curved mounts, allowing you to mount the LEDs in a variety of locations depending on your application for greater versatility. This kit comes with four white LED lights, hardware, switch, relay, wiring and instructions.

Each of the four white LED Rock Light circuits is fitted with weather-resistant connectors and combines using a sealed splitter for a clean installation and efficient operation. If more than four LED rock lights are needed for your application, CJ's Part # 1123239 can be added for four additional white LED rock lights.

Rugged Ridge manufactures Jeep parts and accessories for the growing Jeep and off-road enthusiast market. Rugged Ridge has designed and crafted thousands of products for the Jeep market and continues to develop hundreds of additional Jeep accessories each year.

Order Rugged Ridge's 11232.40 White LED Underbody Rock Light Kit with a Harness and Switch from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Installation Difficulty


Novice skill is required for this installation.

Installation Videos

Video Transcript

When going off-roading, you can never have too much visibility. As you can see with our 2016 Jeep Wrangler, we've installed quite a few LEDs but they're just not quite enough. Today, we're going to take it a step further by installing the Rugged Ridge Rock Light kit. This Rugged Ridge Rock Light kit mounts underneath your Jeep so you can spot rocks or other obstacles when going off road. It includes four LED pods with three LEDs and rubber mounts, and today we're going to install it on our 2016 Jeep Wrangler. For this installation, you'll need a 3/8 ratchet, 5 mm hex key, 10 mm wrench, a drill, 1/4" drill bit, universal drill bit, a set of strippers, cutters, crimpers, a panel removal tool, and safety glasses.

Our Rock Light kit came with a wiring harness and switch, however we're not going to use it. We have a Trail Rocker kit that we're going to wire our lights up into, but you can use the harness that came with the kit. Rugged Ridge has suggestions on where to mount the lights. For the front, they suggest mounting the light on top of the fender liner right there. To mount them they include these rubber mounts where you can either slide the wire through the side and mount it like this, or if you want, you can run the wire through the center and then drill a hole for you to run the wire as well.

We're going to pop this clip off to give us some more room. We're going to drill our mounting holes with a 1/4" drill bit. These bolts are a little bit extra-long, so you can either trim the bolts down or drill another hole in the plastic for the clip right here. Now, because our bolts are a little bit long, we're going to drill another hole right here for that plastic clip. Now, pop down these clips so we can get behind the panel and run the wire. We're going to mount the rear rock lights on the very bottom front part of the rear fender right here. Run the wire through the center hole, then install the bolts. Then, repeat the process on the other side, and then you can move on to wiring.

You want to bring all your wires to a central location to connect them to the pigtail. We have a Painless Performance Trail Rocker, which we'll be wiring our lights into. Connect the ground wire and the power wire. When you're finished wiring, tuck it all out of the way and your installation is finished. Our Rugged Ridge Rock Lights are installed; they look pretty awesome. They'll definitely help out when we're out off-roading. Installation's going to take about two hours, and before you know it, you'll be heading off road.

Vehicle Fitment

This product will fit the following Bronco years:

This product will fit the following F-100 years:

  • 1948,
  • 1949,
  • 1950,
  • 1951,
  • 1952,
  • 1953,
  • 1954,
  • 1955,
  • 1956,
  • 1957,
  • 1958,
  • 1959,
  • 1960,
  • 1961,
  • 1962,
  • 1963,
  • 1964,
  • 1965,
  • 1966,
  • 1967,
  • 1968,
  • 1969,
  • 1970,
  • 1971,
  • 1972,
  • 1973,
  • 1974,
  • 1975,
  • 1976,
  • 1977,
  • 1978,
  • 1979,

This product will fit the following F-150 years:

This product will fit the following Gladiator years:

  • 2020,
  • 2021,

This product will fit the following Wrangler years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.
Complete Your Package
Add to Cart