Seat Track Extender Kit 2005-2014

CJ's Part Number: STE2
CJ's Low Price:
1508198400 31391
Earn 69 RPM Points What's this?
Seat Track Extender Kit 2005-2014
Seat Track Extender Kit 2005-2014 Seat Track Extender Kit 2005-2014 Seat Track Extender Kit 2005-2014 Play Seat Track Extender Kit 2005-2014 Video 1

Product Description

Seat Track Extender Kit for 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 and 2014 Mustangs.

You want to enjoy your Mustang but you're a taller person and the Pony's leg room just doesn't quite cut it. We have the fix for you with this Seat Track Extender Kit that fits all 2005-2014 Mustangs. This kit adds up to three extra inches of leg room in front of your seat so you can get in, get out and drive comfortably. The seat track extenders mount between the seat track and the floor. In the process of moving your seat rearward, it also raises the seat about 3/4". The kit may be used for either the driver side seat or passenger side seat but the kit only modifies one seat.

Kit Includes:
- Two seat track extension bars
- Four 5/16"-24 x 1 grade 8 bolts
- Four 3/8" lock washers
- Two 10mm nuts
- Two 10mm lock washers

Being a taller person doesn't mean you can't enjoy all the Mustang has to offer. Our seat track extension kit will get you in your Mustang and out on the road while not feeling like your cramped up in a small box.

Kit does one seat.

Please Note: When seat tracks are fully extended, the rear seat in your Mustang is not usable.

Similar Mustang Parts

similar Mustang parts More Seat Tracks & Adapters  

Installation Instructions

Mustang Installation

Difficulty: Easy

Mustang Applications

This product will fit the following Mustang years:

Product Reviews

Write a review
Seat Track Extender Kit 2005-2014 is rated 2.9 out of 5 by 11.
Rated 4 out of 5 by from Be patient and it will work I got these as a gift and finally got around to installing. First I don't have a grinder but I used a dremel with a grinding wheel. I took my time and once the fastener was cut I worked the piece that was being removed a little and it came right off. Once I got the seat back into the car the front holes seemed like they weren't going to line up but they did with a little work. I got one lined up and put in a bolt part way, then pulled the opposite track a fraction of an inch by hand and held it in place while I put in the other bolt. After all that it was just a matter of tightening everything up.
Date published: 2016-05-18
Rated 3 out of 5 by from They work....but the install was more "involved" These work. If your tall get a set. I was tired my knee being part of the lower dash; near the radio. They really do as they say and offer more leg room. The issue is that the install took a lot more than I was expecting. The holes didnt match up all that well but you can make it work with more drilling and grinding. Overall im happy with the extender. I suggest doing the install only if you have plenty of time.
Date published: 2015-01-23
Rated 3 out of 5 by from Solid but NOT Precise The product worked as advertised, Cutting off the brackets was a bit trickier than described. The bolt holes did NOT line up right making installation VERY DIFFICULT!
Date published: 2015-04-16
Rated 1 out of 5 by from Horrible the only positive thing I have to say about these is that CJ's customer service is phenomenal. This is my second pair, first pair never arrived but the packaging did. The fitment is horrendous, god awful. I was really looking for to these but I wish I would've look closer into aftermarket seats instead, also worth mentioning I'm 6'8" 340lbs and I can't fully depress the clutch with the seat all the way back. So yes they work but the install makes them not worth it
Date published: 2017-01-06
Rated 3 out of 5 by from Be prepared to modify and have patience Like several other reviewers have claimed, this is NOT a plug and play engineered product. Grinding the factory rivet heads off the stock seat tracks takes patience and time to do it right. Biggest problem is the forward mount holes on the brackets are about 1/4-inch more narrow than the holes on the stock seat channel rails. The stock holes are 16-inches on center while the holes on the brackets are about 15 3/4-inch. Slotting the holes in the seal channel brackets will cure the problem, but just something else to deal with. Second, the factory steel rivets were used to maintain clearance for the seat to move forward. The 5/16-24 hex head bolt heads are so tall with the split washer they restrict the seat from being able for move full forward. I cured this by using 5/16-24 socket cap screws (mushroom head) and black, but that costs another $2 and a trip to the local auto parts store. Third, those same bolts with the kit are silver which make them standout ugly against the flat black rails and brackets. Fourth - the factory trim pieces that snap onto the back end of the seat tracks have to be trimmed to clear the seat track extenders. Not a big deal but just be aware its something else that wasn't mentioned. Otherwise, once you get past all these little mods and hardware issues, the added 3 inches is amazing and finally allows me to fully extend my legs while driving. A little more attention to detail would make a neat idea a great product.
Date published: 2016-11-27
Rated 2 out of 5 by from Great IF You Can Get Them Installed Bought one set of these and the included bolts were too long and the holes didn't line up. Because the included bolts were too long, the bolt was still sticking up almost a quarter of an inch when it started to get tight, which led to a snapped bolt and a ruined extender. Thinking I just had a bad set, I requested and received a replacement from CJ. The second set was NO better than the 1st in terms of bolt length or the holes lining up. Fortunately, a good buddy's family are machinists so they drilled & tapped me new holes that worked a LOT better. The only reason these didn't get one star from me is because, once installed, they are very nice (I'm 6'4"). Just be prepared to provide your own hardware or have a machinist handy if you decide to order them. I literally had an easier time installing my Roush supercharger than I did installing these stupid seat brackets.
Date published: 2015-06-09
Rated 4 out of 5 by from i fit in a sporty car! If you are tall like me (6'8) you need this in your car. As you can see by reading the other reviews most people who reviewed this product had a hard time getting everything to work. Given i did have some small problems, in the end it was fairly simple. follow the instructions step by step and don't read over anything.note you do need a grinder to grind off 2 rivets holding in the front rail brackets. when installing the final product the holes didn't line up but didn't take much to get in the right place. you most likely need two people for the install. after the install it was amazing to sit in a car that truly fit me. something i didn't know until after the install was that the seat doesn't move as foreword as it did with the original rails. so if you have a 5'2 girl friend who likes driving from time to time she will be ticked to know that she cant reach the peddles anymore. overall a great product
Date published: 2015-07-10
Rated 1 out of 5 by from Problems!!!! The seat extenders themselves are a very nice item. Hardware sucks. The front bolts don't clear the track. You need to change our hardware for button head bolts. Also predrilled and tapped holes do not line up. Have to grind river hole on track to line up with ore drilled holes.
Date published: 2017-08-15
  • y_2017, m_10, d_15, h_20
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_11
  • loc_en_US, sid_STE2, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 5.92ms

Product Questions

Do you carry a seat track extender for a 1964 mustang convertible?

Asked by: wink 123
No we do not.
Answered by: rk cjpp
Date published: 2017-09-26

2013 Ford Mustang-Can you use these with power seats?

Asked by: drumguyfuhoma
Answered by: rk cjpp
Date published: 2017-08-28

Are there going to be 15mm bolts in the front brackets I will need to grind off in order to install this in a 2005 Mustang V6 Premium Convertible? This track extender kit becomes the new brackets installed to the seat themselves and floor board?

Asked by: KountryKat
you reuse the bolts, what you grind off is what holds the front of the bracket where the front bolts go. I did this today on my 2006 convertible.
Answered by: stringfellow
Date published: 2016-05-19

Do you have a seat track extender for a 2014 ford Taurus?

Asked by: brasco817
No we don't.
Answered by: rk cjpp
Date published: 2016-01-07

Has the problem of the holes not lining up on the 2014 mustang seat extenders been corrected by the manufacture yet? The review of this product said there was a problem fitting them becuse of this.

Asked by: bob 53
Doesn't appear to be an isolated case to me if you read all of the reviews.  Still a problem now.
Answered by: dougmay2
Date published: 2015-07-07

Does anyone have a picture of the "Rivot" everybody says needs to be ground off?

Asked by: EMD21102
My 2011 had two man sized rivets that required grinding ..... took a good 30 minutes with an angle grinder and cold chisel and hammer. Probably depends on the year.
Answered by: dougmay2
Date published: 2015-07-07

is the instillation really that bad? i would be totally sold if there was a video showing how the install should be done.

Asked by: shaneh
Yes it is that bad!  The manufacturer needs to listen to its customers and make some adjustments in the instructions and hole alignment on the brackets.  An angle grinder is a must to grind off the old rivets on the seat track.
Answered by: dougmay2
Date published: 2015-07-07

Ok with stock power drivers seat?

Asked by: Topless
Yes, this will work with the stock power driver side seat.
Answered by: CJPP Staff
Date published: 2015-04-24
  • y_2017, m_10, d_15, h_20CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_8
  • loc_en_US, sid_STE2, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 5.67ms

You Might Also Like

Product Video

Seat Track Extender Kit 2005-2014 Video Transcript
By Bill Tumas: We’re here with a pair of seat track extenders fitting all 2005 through 2014 Mustangs.

If you're a taller driver and are looking for more room in your 2005 through 2014 Mustang, these seat track extensions are an excellent choice. This is going to bolt to your factory seat tracks to give you 3 additional inches of leg room in the front seat of your Mustang. It includes a pair of these brackets here which are going to bolt to your seat track, and enough to do one seat. The hardware is included, and when installed it will lift the seat roughly 3/4 inch higher, and when the seat's all the way back it will touch your back seat, making the backseat not usable.

Again, these seat track extenders are sold as a set which do one seat. If you're looking to both fronts, you'll want to order two sets.