Shift Knob 2-1/8" GT/CS Rally III With Shift Pattern 5-Speed California Special 2007-2009

CJ's Part Number:

Rally III 2-1/8" GT/CS Shift Knob with a 5-Speed Shift Pattern for all 2007, 2008 and 2009 California Special Mustangs with a Manual Transmission.

If you’re looking to switch up the original shift knob in your 2007-2009 California Special Mustang, then add just the right touch of color to your interior with this new rally III 2-1/8” shift knob featuring a 5-speed shift pattern and GT/CS logo! These California Special inspired shift knobs are designed with bold colors and rally III style stripes in a high gloss finish that give your Mustang’s interior a classic, yet custom look that every enthusiast will appreciate.

Features and Benefits:
- Available in an Assortment of Colors
- Correct 5-Speed Shift Pattern (Reverse on the Bottom Right)
- Inlaid Rally III Style Stripes
- Etched GT/CS Logo
- Made Using High Quality Partek Resins
- Engineered for Strength and Durability
- 2-1/8” Diameter and 12mm x 1.25 Thread Pattern
- Made in the USA

What are Rally III style stripes? The Rally III stripes consist of three separate stripes; two small outer stripes surrounding a wide inner stripe. These stripes run horizontally on the driver and passenger side of the shift knob to simulate rocker stripes. With this specific knob, the GT/CS Logo is located within the Rally III stripe on both the driver and passenger sides.

These manual shift knobs are made in the USA using the same high-quality partek resins found in world-class billiard balls, and are engineered for long-term strength and durability. Choose from a variety of stripe and color combinations that suit your individual taste. Color options are listed by knob color, then stripe color. The GT/CS logo on either side of the knob is the same color as the shift knob. The rally stripes and shift pattern are all inlaid and polished smooth to the touch and guaranteed to last the life of your vehicle.

This custom shift knob features a 2-1/8" diameter and the correct 12mm x 1.25 thread pattern for your 2007-2009 GT/CS 5-Speed Manual Transmission Mustang.

*All knobs are custom made to order and take 3-4 weeks to ship from CJ Pony Parts.
*Will also fit 2005-2010 V6 and GT Manual Transmission Mustangs. 

Please Note: This manual shift knob does not include a jam nut. However, a jam nut or threaded shift boot retainer is required to make sure the shift knob is properly aligned when tightened on the shift handle. A shift boot retainer is recommended instead of a jam nut as it will prevent a gap between the new shift knob and the factory boot. Without a jam nut or shift boot retainer you run the risk of splitting the shift knob in half if you over tighten knob when it bottoms out on the shift handle.

Installation Videos

Video Transcript

If you're looking for any easy upgrade for the interior of your Mustang, you can't go wrong with an aftermarket shift knob. Here at CJ's we have a huge selection, including these 2 1/8" diameter USA made knobs, available in 13 colors. With or without stripes, with your choice of graphic, there's over a thousand different options available.

You should have no trouble finding one that looks great in your Mustang.

Installation for the shift knob is very easy. If you're early Mustang you'll have to thread on this jam nut. If you're '05 and up, we carry these retainers that will hold your boot in place once you install the after market knob.

All the knobs are available in solid colors, without any graphics whatsoever. If you chose to go with a graphic, we offer the 5.0, the running horse, the snake, the GT, as well as a Boss 302. If you choose to go with a pattern, stripes are available as well. And if you prefer, you can actually have the graphic added to the side.

In our case, we had this custom one made for our CJ race car with our CJ emblem on the side. We'll be installing this one.

Since quarter mile performance has been the goal with our gotta have it race 2013 GT, we're still running the stock shift knob. We'll remove this one and install our new green knob. Get a good grip on the knob and turn it counter clockwise.

First step for the installation of the new knob is to install its retainer. The retainer's gonna hold the boot in place and also work as a jam nut for the knob. Thread your retainer down until it's touching your shift boot. Grab your shift knob, line up the threads. Start threading it on. Now, if you thread it all the way down, it probably isn't gonna line up straight.

What you'll wanna do then is loosen it up until it's about an eighth of a turn from straight, thread the retainer upward. Get a good grip on it, turn it until it's straight. As you can see our shift knob was a nice additional upgrade to our interior. It only took a few minutes to install. You'll be back on the road in no time.

Vehicle Fitment

This product will fit the following Mustang years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.