Under The Sun Inserts Grille Insert USA Flag Jeep Wrangler JL 2018-2021/ Gladiator 2020-2021

Under The Sun Inserts:
88% of 100


  • Printed Using UV Ink
  • Automotive Clear Coat Finish
  • Aluminum Construction
  • Easy To Install
MSRP $137.49
You save $2.49

Under the Sun Inserts USA Flag Grille Insert for 2018, 2019, 2020 and 2021 Jeep JL Wranglers and 2020-2021 Jeep Gladiators.

Have you been thinking about adding some custom-looking touches to the exterior of your 2018-2021 JL Wrangler or your 2020-2021 Jeep Gladiator? Then this all-new Under the Sun Inserts USA Flag Grille Insert (JL-OLD-GLORY) is calling your name!  

Features and Benefits:
- Fits Brand-New 2018-2021 Jeep JL Wranglers or your 2020-2021 Jeep Gladiators
- Powder-Coated Aluminum Construction
- Printed Using UV Ink
- Automotive Clear Coat Finish
- Iconic American Flag Design
- Easy to Install

It can be hard finding upgrade parts and pieces for your newer Jeep, but that's why Under the Sun Inserts designed this USA Flag Grille Insert! It's manufactured from high-quality aluminum with UV ink and depicts the iconic Old Glory. It's a perfect fit to your Jeep's front grille and will easily slip into place, giving your Jeep a high-end, upgraded look and feel. 

Please Note: This grille insert will not work in conjunction with any other aftermarket grille inserts. Not for use on 2020-2021 Jeep Gladiators with a front facing camera.

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

Today on CJ Off Road we're going to give a custom look to the front end of our JL.

If you're looking to add a more custom touch to the front end of your JL Wrangler then today we're going to be installing this Under The Sun insert featuring the American flag design fitting your brand new 2018 Jeep JL Wrangler.

This Under The Sun grill insert features a powder hood aluminum construction using UV resistant ink. That way it won't fade while you're out in the sun.

It has an automotive graded clear coat and features an American flag design to give you more patriotism in the front of your Jeep Wrangler.

It's a super easy installation. With that being said, let's get it installed.

Tools needed for this installation, long flathead screwdriver, stubby flathead screwdriver, Phillips-head screwdriver, and a T20 torques bit.

We're going to start by popping the hood and removing the grill. Let's get started. Just like in the JK there are six push pins to hold the top of the grill on. I'm using flathead screwdriver. Just pop the inner section out about halfway, go underneath, pull it right out, set these aside. You'll be reinstalling them.

After you have all six push pins removed, you can pull the grill out. It comes right out towards you, just like the JK did. There's a couple of push pins. Work your way over to the other side, pull it right out nice and smooth.

Once you have the grill out, flip it upside down on the table. We have to pull out all the slot covers in here, see if it's a nice cover, however we've got to pull them out. It takes a couple screws, but it's not too long.

The first thing I'm going to remove are the seven plastic push pins. There's four along the center of the grill here, and then three along the base. Use a small flathead screwdriver to pry on this smaller side. All you have to do is push down on the clasp and then they'll pop right out, set these aside.

We're going to start moving the torques bolts. They use a T20 socket. There's a few of them as well as a few Phillips-head bolts.

After you have all the torques bolts removed, then you can pull out the Phillips-head screws. There are a few plastic retention clips that have to be popped off. There's going to be two over here as well as a few throughout the inside. We're going to start with this top corner here. There's an overlapping plastic piece. Make sure that's pulled over the top of it. Grab the same flathead screwdriver, go in between this grill cover, and that piece, go in there, pop it towards you and give a little pull on that. You see how that pulls out? Repeat the exact same process on the all the rest of them.

After you have all the clips removed, pull out the grill insert. Go ahead and grab the grill insert and actually place it in. You're going to put it upside down. Obviously that way it's facing on the outside. Once it's in there you can kind of even it up. Fits inside the slots really nicely, then you can reinstall the grill back into the Jeep.

Start with the bottom clips. They should pop right back in. There's one right under the headlight here, on both sides, then reinstall your push pins. Close your hood and your installation's complete.

We just wrapped up the installation of the American flag Under The Sun grill insert on our brand new JL Wrangler. This insert looks really awesome and it only takes you about 20 minutes to get it installed. It shows the American pride on the front end of your Jeep and gives it a really custom look. To find it as well as many other great parts for your JL, check out CJPonyParts.com.

Vehicle Fitment

This product will fit the following Gladiator years:

  • 2020,
  • 2021,

This product will fit the following Wrangler years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.