UPR Dual Valve Oil Separator Black EcoBoost 3.5L F-150/Raptor 2017-2019

UPR:
5030-221-1
Rating:
98% of 100

Highlights

  • 16oz Capacity Can
  • Plug And Play Installation
  • Show Quality Finish
  • Multi-Chamber Design Traps
MSRP $479.99
$399.99
You save 17%

UPR Black Dual Valve Oil Separator for all 2017, 2018 and 2019 3.5L EcoBoost F-150s and 2017, 2018 and 2019 F-150 Raptors.

UPR knows what they are doing when it comes to aftermarket catch cans and this UPR 5030-221-1 Black Dual Valve Oil Separator for your 2017-2019 3.5L F-150 EcoBoost or Raptor proves that beyond a shadow of a doubt. The Ultimate Oil Separator features a UPR Plug N Play™ Dual Valve Catch Can with UPR Pro-Series Check Valves one way electronic pressure sensor system to deliver improved fuel economy, throttle response and performance.

Offering the largest capacity in a compact design, this dual valve oil separator will eliminate oil vapors on vehicles that are normally aspirated or power added equipped. This system is designed to require less maintenance between oil changes and eliminates the amount of moisture that's collected during condensation control by being mounted in the engine bay. Our Patented Multi-Stage Multi-Chamber internal design is the best for controlling oil vapor and mist even in the hottest mounting locations. Most importantly this dual valve oil separator keeps your PCV system performing with the level of protection and performance it deserves by not filling the intake and CAC / Inter-cooler full of oil like the factory designed system does.

Features and Benefits:
- High quality T-6 6061 CNC machined billet aluminum
- Plug N Play ™ fittings all the way around catch can
- 16oz capacity can (6" x 3")
- Show quality finish
- Nickel T fittings and drain cock
- Prevents oil from entering intake
- Patented multi-chamber design traps oil
- Improves fuel economy, throttle response and performance
- 5/8" oil resistant continental braided hose included
- Black color scheme
- Require drilling your factory inlet for the WOT connection
- Easily installs in 30-40 minutes

Manufactured from Domestic T-6 6061 Aluminum bar stock and finished off using only the best Diamond cutters, UPR's 5030-221-1 Black Dual Valve Oil Separator exceeds your expectations of what a superior product should fit and look like. The fittings and drain cock are manufactured from Nickel T. Along with all the hardware you'll need for installation, a 5/8" oil resistant continental braid hose is included.

Order this UPR 5030-221-1 Black Dual Valve Oil Separator for your 2017-2019 3.5L EcoBoost F-150 or 2017-2019 F-150 Raptor  today from CJ Pony Parts.

California Residents: Proposition 65 Warning

Note: This item is not CARB (California Air Resource Board) exempt and is not legal for sale or use in the state of California.

Installation Difficulty

Easy
Easy

Novice skill is required for this installation.

Installation Videos

Video Transcript

One of the very first things you should do to your EcoBoost F-150, whether it's just the F-150 or the Raptor, is an oil separator, because it's direct injection. So today we're gonna be installing this UPR Dual Oil Separator, fitting your 2017 F-150 EcoBoost, and the F-150 Raptor. This UPR Oil Separator makes sure that your 3.5 liter EcoBoost is running good and clean, to catch the oil from the PCV valve, preventing it from entering the engine. It's made of high-quality CNC machine-built aluminum, with a black anodized finish, and a drain valve on the bottom to make it easy to service. It comes with all the hardware and hose you'll need for an easy installation, so today we're gonna install it on our 2017 Raptor.

Tools you'll need for this installation: 7mm socket, 8mm socket, 10mm socket, an extension, 1/4" ratchet, 17mm socket, 5/16" hex key, a 3/8" ratchet, a trim panel removal tool or a flathead screwdriver, a 51/64" drill bit or a universal drill bit, a drill, and safety glasses. All right. Installation of this oil separator is pretty straight forward. The first thing I'm gonna do is remove the factory air inlet off the factory air box. Remove the two clips on the front of the inlet. Once you get the two clips off, there's an 8mm screw holding the air inlet to the air box. Then the air inlet simply just pops off, and set it aside. There's two nuts that hold the engine cover on, that you have to remove. Once you remove the two nuts, just lift up on the engine cover.

We're ready to install the oil separator. Make sure we install it, the valve is closed. Make sure your fittings are in good and tight. Now we're gonna install it down here on the frame. Now, getting this bolt back here is kind of tricky. Then you can tighten the bolt with a 17mm socket. And with a 5/16" hex key, you can tighten the bolt in the position you want the catch can. Just like that. Go onto the passenger side of the engine and pull on the gray tab to remove the PCV hose from the engine, and then also the intake manifold. Grab the hose in the kit that is pure braided hose, there's no check valves in it. This is going to be the dirty hose, and this is gonna go on top of the oil separator, and then to the passenger side of the engine. Connect it to the engine where you just removed the PCV hose. The other end of this dirty hose goes to the top port on the oil separator.

The clean line is now ready to be installed, and this is the line with the check valve, with a 45 degree fitting on one end, and a straight fitting on the other. This 45 is gonna go on the oil separator, and the straight part will go right on the intake manifold. Connect it right to the intake manifold where the factory PCV hose went. The end with the check valve can go right here on the front of the oil separator. The final line to install is the wide-open throttle line. The part with the 45 degree end will go on the can, and then this part's gonna go on the turbo inlet tube on the passenger side. Loosen this clamp right here to remove the turbo inlet pipe. There's one more clamp on the turbo we have to remove to completely remove this pipe. To easily access the clamp holding on the inlet pipe to the turbo, go through the fender well on the passenger side, then use a 7mm socket to remove the clamp, and simply remove the pipe. It's kind of hard to see, but it's really not hard to get to. All you'll need is a 7mm socket and an extension, and it's right here in the fender well. With both clamps removed, just simply remove the pipe.

This is very approximate and not super crucial, but we're gonna be putting the inlet for this wide-open throttle line right about here; 1" down from this line, and 1" over from this canister area. Grab yourself a 51/64" drill bit, or a universal bit, and drill it out. Install the supplied grommet into the hole that you just drilled out to 51/64". Install the supplied fitting into the grommet. Using a little bit of WD-40 will make this a little bit easier. Before you actually install this back on the Raptor, make sure you clean it out with compressed air, or water, or whatever. Make sure it's nice and clean, then you can reinstall it.

Reinstall the inlet pipe the same way that you removed it, and then tighten both clamps. Once you get the inlet tube installed, you can now connect the wide-open throttle line to the fitting you just installed. Okay, we have the whole UPR Oil Separator installed. All that's left to do now is reinstall the air inlet. Reinstall the two clips and the screw. Reinstall the engine cover if you choose to do so. Then your installation's finished.

Okay, we got our UPR Oil Separator installed. It's gonna keep this Raptor running clean and smooth for a long time. Installation is not too bad, should take you less than an hour, and before you know it, you'll be heading off-road.

Vehicle Fitment

This product will fit the following F-150 years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.