JLT Cold Air Intake Kit Fenderwell Series 2 Black Textured Bullitt 2001

JLT Performance: CAI2-FMB-01
CJ's Low Price:
$289.05
1464652800 4307
Earn 289 RPM Points What's this?
JLT Cold Air Intake Kit Fenderwell Series 2 Black Textured Bullitt 2001
JLT Cold Air Intake Kit Fenderwell Series 2 Black Textured Bullitt 2001 Play JLT Cold Air Intake Kit Fenderwell Series 2 Black Textured Bullitt 2001 Video 1 Play JLT Cold Air Intake Kit Fenderwell Series 2 Black Textured Bullitt 2001 Video 2
JLT Performance

Product Description

JLT Black Textured Series 2 Fenderwell Cold Air Intake Kit for all 2001 Bullitt Mustangs.

Using the original JLT cold air intake as a guide, JLT molded, scuplted and perfected everything until they had the best looking, fitting and performing system you can buy. The all new JLT Series 2 intake tube is 4-1/4" ID, roto molded plastic for it's resistance to engine heat while keeping the intake air charge nice and cool. No metal tubing here! Gains of 14-20 RWHP are typical with this kit.

The MAF and air filter have been relocated into the fenderwell for a cooler intake charge. Works with both 80mm and 90mm MAF's, there is no need to buy additional parts when you upgrade to a 90mm MAF.

The best part about the new Series 2 intake is JLT kicked the cool factor up a notch and molded a 105mm MAF housing right in the tube. Now you have a kit you can grow into and not have to buy a complete new kit when you reach 550-600 RWHP. Putting a Whipple, Kenne Bell or Eaton blower swap on your Bullitt? Simply drill out the pre-molded plug on the MAF block located on the bottom of the tube, discreetly out of sight. Install your SCT MAF sensor electronics, add a huge 4-1/2x12 S&B Powerstack air filter and you've now changed your JLT Cold Air Intake into a JLT High Boost 12" Intake. Molding the MAF into the tube makes for a much smoother air flow with no couplers, reducers or separate MAF housing and can support 800+RWHP.

Kit Includes:
- JLT Plastic Intake Tube
- Silicone Coupler
- Silicone Reducer
- Apron Plate
- Powerstack Air Filter
- Silicone MAF Spacer
- MAF Adapter
- MAF Adapter Gasket
- Heavy Duty Clamps
- All Necessary Hardware

Please Note: This JLT Cold Air Intake is CARB Approved (D-761)

*Will NOT fit with most strut tower braces.

Available with a black textured finish or painted to match your Bullitt Mustang. The two digit code after each color in the drop down menu is the Ford paint code. Please verify your Mustang's paint code prior to ordering.

If you're looking for some of the best cold air intakes and performance parts for your Mustang, go no further than CJ Pony Parts' selection of parts from JLT Performance. With more than several 1999-2004 Mustang parts available, you can find exactly the cold air intake you need for your performance Mustang-just check out the selection of JLT Performance parts from CJ Pony Parts today.

Purchase a new JLT Series 2 Fenderwell Cold Air Intake Kit for all 2001 Bullitt Mustang from CJ Pony Parts today!

 

Installation Instructions

Mustang Installation

Mustang Applications

This product will fit the following Ford Mustang years:

Product Reviews

Write a review
  • bvseo_sdk, p_sdk, 3.1.0
  • CLOUD, getContent, 24.52ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 403 was returned;

Product Questions

  • bvseo_sdk, p_sdk, 3.1.0
  • CLOUD, getContent, 28.86ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: HTTP status code of 403 was returned;

You Might Also Like

Product Video

JLT Cold Air Intake Kit Fenderwell Series 2 Black Textured Bullitt 2001 Video Transcript
By Bill Tumas: We're here with a JLT cold air kit specifically designed for your 2001 Mustang Bullitt. The cold air kit is designed to fit the unique throttle body used on the Mustang Bullitt. It's available on a black plastic finish, as well as painted in the factory black, true blue or dark highland green color. It includes the tubing, silicone couplers, a reusable filter, and all necessary hardware, including mass air adapters. The JLT looks great under the hood, and it increases performance by mounting the filter down on the fender, to get it out of the hot engine bay.