Paint Black Trim Aerosol 1969-1970

CJ's Part Number: PTTB
CJ's Low Price:
1490486400 28144
Earn 19 RPM Points What's this?
Paint Black Trim Aerosol 1969-1970
Paint Black Trim Aerosol 1969-1970 Play Paint Black Trim Aerosol 1969-1970 Video 1

Product Description

Black Trim Aerosol Paint for 1969-1970 Mustangs.

This is the correct color paint for 1969-1970 Mustang louvers and rear spoilers. Can be used for other applications.

Similar Mustang Parts

similar Mustang parts More Paints & Dyes  

Installation Instructions

Mustang Installation

Mustang Applications

This product will fit the following Mustang years:

Product Reviews

Write a review
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 185.29ms
  • bvseo-msg: HTTP status code of 404 was returned;

Product Questions

  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 145.75ms
  • bvseo-msg: HTTP status code of 404 was returned;

You Might Also Like

Product Video

Paint Black Trim Aerosol 1969-1970 Video Transcript
By Bill Tumas: We recently replaced the cowl grill on our 1990 Mustang Convertible. It really cleaned up the front of our car, but unfortunately, sometimes, when you add new parts, some of the older stuff looks a little more worn out. We're noticing a lot of wear on our lower windshield moldings, so today, I'm going to show you how to replace those as well. For this installation, you'll need a Phillips head screwdriver, panel removal tool, and a small pick.

To remove the lower windshield molding, we have to remove our cowl first and then the outer pillar trim, as well. To remove the wiper, simply lift up on the arm, pull out the tab here. Press it back down and slide it off.Now, we're going to remove the six screws that hold the cowl to the body, lift up to move the washer hose, and put our cowl aside. We'll need to remove this thin windshield weather stripping to get this outer panel off. We want to get a small pick, go right down here in the corner, and pull it out.

You want to grab a panel removal tool, slide underneath the panel, and just twist to release. We don't have to take it all the way off. Now, we can access our molding. We're going to remove the original molding and you can just pop it off the clips. The lower windshield molding is held on by these two metal tabs. Many times the original plastic clips will be broken off. You want to remove them before you install the new panel.

We'll give the area a quick cleaning before we install the new pieces. To install the new molding, you'll align these two clips up, two metal tabs, put it in the center and press downward. At this point, you can reinstall your pillar. Taking a close look at ours, it's also pretty faded. Again, with the new part here, this will probably look pretty worn.

We're going to remove this the rest of the way, give it a quick coat of paint before we put it back on. Simply pull it outward, slide it down, and out. Give it a quick scuff with a Scotch Brite. Then I'll wipe it down with a little bit of rubbing alcohol. Let it dry for a couple minutes and be ready for paint. Now, we'll give it a couple coats of trim black.

We'll give that some time to set up before we put it back on the car. We're going to reinstall our new painted pillar piece and then we want to attach this weather stripping to the pillar before we press it down into place.

Once you've repeated the process on the other side, we're ready to reinstall our cowl. Please don't forget to hook up the washer hose. Again, you're screwing in the plastic here so make sure you make them snug but don't over tighten them. The last step, reinstall the wipers and our installation's finished.

New trim panels and a little bit of paint made a huge difference in the look of our Mustang. If you're just looking to replace the trim, you'll need about a half an hour of labor total. If you're going to paint like we did, I'd say give yourself an hour to do the whole job. You'll be back on the road in no time.