Ford Performance GT350/GT350R Intake Manifold for all 2015, 2016 and 2017 Mustangs with 5.0L and 5.2L Engines.
It’s time to give your 2015-2017 Mustang GT some race-inspired performance with this GT350/GT350R Intake Manifold (P/N: M-9424-M52) from Ford Performance! Original equipment on the naturally aspirated, flat-plane crank GT350/GT350R Voodoo engine, this will fit any of the Second Generation 5.0L 4-Valve “Coyote” engines used in all 2015, 2016 and 2017 5.0L GT Mustangs.
Made from a light-weight composite material, this intake manifold features high-quality fitment and performance. You will notice significant power increases above the factory 2015-2017 Mustang GT intake manifold with no loss of torque. The runners are tuned for 7500rpm peak power and are compatible with the production Ti-VCT 5.0L fuel rails. This intake manifold features pre-assembled and pre-installed charge motion control valves (CMCV) to retain near stock driveability characteristics. This Ford Performance GT350/GT350R Intake Manifold is for your 2015-2017 Mustang with 5.0L or 5.2L Engine and also includes new intake manifold and throttle body O-ring gaskets.
Features and Benefits:
- OE on ALL 2015-2017 Shelby GT350 and GT350R Mustangs
- Fits ALL 2015-2017 5.0L GT Mustangs
- Increases Airflow to Deliver More Performance
- Designed to Offer Peak Power at 7500rpm
- Pre-Assembled with Charge Motion Control Valves
- Made from Light-Weight Composite Material
- Includes New Intake Manifold and Throttle Body O-Ring Gaskets
- Made in the USA
*Requires a throttle body adapter to properly use a 2015-2017 Mustang GT specific throttle body (See P/N: TBA2).
*Requires custom calibration, NOT included (See P/N: NG4-V).
*NOT compatible with the factory 2015-2017 Mustang GT strut tower brace (Use P/N: M20201GT350).
Please Note: Minor modifications to a few vacuum lines will be necessary for proper installation on any 2015-2017 Mustang GT, you will also have to slightly extend a small wiring harness to complete the install. The vacuum components, fittings and additional wiring are NOT included.
If you're looking for parts for your Mustang, you should start by looking at the great selection of parts that CJ Pony Parts offers from Ford Performance (formerly Ford Racing). By buying your Ford Performance parts from CJ Pony Parts, you know you're getting your Mustang parts from a reliable, reputable dealer, since CJ Pony Parts is a Top 10 Ford Performance Dealer and has been for the last 10 years.
Manufacturer Part Number: M-9424-M52
Order this Ford Performance GT350/GT350R Intake Manifold for your 2015, 2016 or 2017 Mustang with 5.0L or 5.2L Engine from CJ Pony Parts today!
Product ReviewsWrite a review
I have a 90mm throttle body will it fit gt350 intake perfect or do i have to but a blowfish adapter?
Will the gt350 throttle body still work on the 5.0?
I have a Raush cold air intake and Raush tune. Will a new tune be required to get the most out of the GT350 intake?
You Might Also Like
CJ's Low Price:$349.00
CJ's Low Price:$175.00
This GT 350 Manifold from Ford performance is made of a lightweight composite materials made right here in the USA. Again, it's going to be a direct replacement for your factory intake and normally requires a GT 350 Throttle Body, but we actually have a better solution than that.
One of the drawbacks to running the GT 350 Intake Manifold on your GT is the tuning, because if you're running the GT 350 Throttle Body, it's very hard to get the tuning just right. You can have surges and all kinds of performance problems. At CJ's, we have the perfect solution with this exclusive adapter plate. This will bolt on to the GT 350 Manifold, and allow you to run your stock and GT Throttle Body or an equivalent aftermarket Throttle Body making tuning much easier.
This GT 350 Manifold from Ford Performance will work with both natural gas or super charged applications as a great way to pick up high RPM horsepower.