Replacing the Fender Emblem and GT Trunk Badge on Your S650 Mustang

The new 2024 Ford Mustang GT brings back the iconic 5.0 badge on the front fenders, signaling the potent 5.0-liter Gen 4 Coyote V8 engine under the hood. For many owners, adding or replacing the fender emblem or the GT badge on the trunk is a great way to customize the look of their ride.

How to Replace the Fender Emblem on Your 2024 Mustang

In this guide, we'll show you step-by-step how to replace the front fender 5.0 emblem and GT trunk badge on your S650 Mustang GT. You can easily apply or replace the 5.0 fender emblems or GT badge with a few basic tools and some simple techniques. Dress up your new S650 GT with a fresh set of 5.0 emblems to overhaul the appearance of your ride.

We're installing the Bronze Ford Fender Emblem found on the Bronze Appearance Package, but the process is largely the same for any emblem. Check out the video below for more information on the installation.

Tools and Products Needed

• Fishing line OR Plastic Pry Bar
• Rubbing Alcohol
• Clean Microfiber Cloth
• Painter's Tape

Step 1: Mask the Surrounding Area

Use painter's tape to mask off the area surrounding the emblem. This protects the paint before you start removing the emblem.

Step 2: Remove the Emblem

You can use a plastic pry bar or fishing line to remove the emblem. Work your way under the emblem and loosen it from the fender.Then, gently lift up the emblem and remove it.

Step 3: Remove Leftover Residue

Remove any leftover glue residue with your fingers. This should be relatively easy since the glue is new. If you're having trouble, use a safe-on-paint remover to help.

Step 4: Clean the Area

Use isopropyl or rubbing alcohol and a microfiber cloth to clean the area where you removed the emblem. You want to remove any leftover residue that you couldn't get off with your fingers.

Step 5: Remove the Tape

Now, remove the masking tape.

Step 6: Install the New Emblem

Line up your new emblem with the factory alignment tabs and then press it into place. Be sure that you press evenly along the entire length of the emblem to help it adhere properly.

Step 7: Repeat This Process

Now that you've finished one side, repeat steps 1 to 6 on the opposite side.

Bronze GT Trunk Badge Install Instructions

Adding a bronze GT trunk badge from Ford will follow the same process as replacing the 5.0 emblem with a few minor differences. Check out the video and step-by-step guide below for a full breakdown of how to install a new bronze Mustang GT trunk emblem.

Tools and Products Needed

• Fishing line OR Plastic Pry Bar
• Rubbing Alcohol
• Clean Microfiber Cloth
• Painter's Tape

Step 1: Clean the Badge Area

Use cleaning fluid and a rag to wipe down the factory badge and the paint surrounding it. Remove any dirt or residue for a clean application surface.

Step 2: Protect the Paint Around the Badge

Cover the paint around the factory badge with painter's tape. This will protect the paint while you remove the badge.

Step 3: Remove the Badge

Use a plastic pry bar to slowly work your way under the badge and pry it free from the trunk. Alternatively, stretch out a strand of fishing line, slide it beneath the badge, and slowly move it back and forth until the factory badge separates from the trunk. Then, gently lift up the emblem and remove it.

Step 3: Remove Adhesive Residue

Remove any leftover glue residue with your fingers. Roll the glue by sliding your fingers along the paint until the adhesive separates from the trunk. If you're having trouble, use a safe-on-paint adhesive remover.

Step 4: Remove Tape and Clean Area

Remove the painter's tape. Then, use isopropyl or rubbing alcohol and a microfiber cloth to clean the area where you removed the badge.

Step 6: Apply the New Badge

Align your new bronze GT badge with the factory holes on the trunk, and press on the tabs until you hear them lock into place. Be sure to press evenly along the entire length of the badge to help it adhere properly.

Easily Change up the Look of Your Ride with Aftermarket Badges and Emblems

Replacing the factory GT badge or 5.0 emblem on your 2024 Mustang GT is an easy mod that can be done with things lying around your house. It's a quick way to add a personal touch to your S650 without breaking the bank. If you're considering adding other badges or emblems to your S650, we offer plenty of different options to fit your Mustang's style. Shop our wide selection of Mustang badges and emblems below for an easy aesthetic upgrade.