AMK Products Master Engine Fastener Kit Shelby Cobra GT500KR 1968

This Master Engine Fastener Kit from AMK Products includes 165 total pieces of factory correct, OE style fasteners that are required to properly reassemble the engine components which attach to the long-block on your 1968 Shelby Cobra GT500KR's 428 Cobra Jet engine. This kit is specifically assembled for all 1968 Shelby Cobra GT500KRs.

AMK Products' Master Engine Fastener Kit includes individually packaged sets of hardware for various applications on your 1968 Shelby Cobra GT500KR's 428 Cobra Jet engine. Each package is thoroughly labeled so you know exactly where it goes on your FE big block engine. The individual sets of hardware also include the total number of pieces that are required for the specific application. Most of the included fasteners are either meticulous reproductions of the originals or new old stock!

Master Engine Fastener Kit Includes:
- Air Cleaner with Holley Carburetor: 2.6" Double End Stud, Wing Nut (2)
- Air Cleaner Shroud and Tube: External Nut/Washer Assembly, Hex Washer Head Sheet Metal Screw (5)
- Air Cleaner Snorkel: Hex Washer Head Screws (2)
- Carburetor: Studs, 7/16" Nuts (8)
- Crank Pulley: Hex Place Bolts (3)
- Crankshaft Damper: Hex Bolt, Flat Washer (2)
- Distributor: Hex Screw/Split Washer Assembly (1)
- Distributor Points and Condenser Single: Slot Pan Head Machine Screws (3)
- Distributor Vacuum Unit: Slot Pan Head Screws (2)
- Engine Block Drain Plugs: External Hex Pipe Plugs (2)
- Engine Fan to Clutch: Hex Screw/Split Washer Assembly (4)
- Engine Fan Clutch to Water Pump: 7/16" Hex Screw/Split Washer Assembly, "SEMS" (4)
- Engine Lift Hook: Left Side Hex Bolt (1)
- Exhaust Manifolds: Special Ramp-Lok Hex Bolts, 2 with Studs (32)
- Fuel Pump: Hex Screw/Split Washer Assembly (2)
- Ignition Coil Strap and Bracket: Hex Screw/Split Washer Assembly, Hex Washer Head Screw, Hex Nut (3)
- Intake Manifold: Hex Place Bolts, Spacers (12)
- Oil Filter Adapter: Hex Screw/Split Washer Assembly (4)
- Oil Pan: Special Hex Screw/Split Washer Assembly (20)
- PCV Hoses: Wire Clamps (4)
- Starter: Hex Screw/Split Washer Assembly (3)
- Timing Cover: Hex Washer Head Screws, Hex Bolt, Hex Machine Screws (10)
- Aluminum Valve Covers: Hex Bolts "RBW", Flat/Split Washers (30)
- Water Neck: Hex Screw/Split Washer Assembly (2)
- Water Pump: Hex Screw/Split Washer Assembly, Hex Bolt at Lower Right Side (4)

Buying individual sets of engine hardware for your 1968 Shelby Cobra GT500KR's 428 Cobra Jet engine can be expensive and time consuming if you're not sure which hardware you need. This Master Engine Fastener Kit makes it easy by including authentic style hardware that specifically fits your 1968 Shelby Cobra GT500KR. With a Master Engine Fastener Kit from AMK Products, you will not only save time and money, but you will have the confidence knowing your 1968 Shelby Cobra GT500KR's 428 Cobra Jet engine is going to be reassembled with the finest factory correct hardware on the market!

AMK Products produces the most factory correct hardware for your classic Mustang. No matter what kind of Mustang you're building, there's no company better for nuts and bolts than AMK Products!

*Not for use on 1968 Shelby Cobra GT500s which are equipped with the 428 Police Interceptor engine.