Flowmaster Cold Air Intake System Delta Force EcoBoost 3.5L F-150 2017-2018/F-150 Raptor 2017-2018
Flowmaster Delta Force Cold Air Intake System for 2017-2018 3.5L EcoBoost F-150s and 2017-2018 F-150 Raptors.
Are you interested in getting some pretty significant horsepower and torque gains in your 2017-2018 3.5L EcoBoost F-150 or F-150 Raptor? If so, you should definitely take a closer look at this Flowmaster Delta Force Cold Air Intake System that’s now available from CJ Pony Parts!
Delta Force Cold Air Kit Features:
- Up to 15% Gain in Horsepower and Torque
- Custom-Molded Black Cross-Linked Polyethylene High-Flow Intake Tube
- Aircraft-Quality Black Anodized Aluminum Fittings
- High-Quality Reinforced Silicone Couplers and All Stainless Steel Hardware
- Serviceable Lifetime Large Diameter High-Flow Conical Shaped 8-Layer Cotton Gauze Air Filter
- Filter Traps More Dirt Than Typical 6-Panel Designs
- Custom-Fit Black Powder-Coated Air Dam with Attachment Brackets to Securely Mount System
- Soft Bumpers Eliminate Metal-to-Metal Contact Under Hood
- Easy to Install: No Cutting or Drilling Required
- No Tuning Necessary
- Made in the USA
- Fits All 2017-2018 3.5L EcoBoost F-150s and F-150 Raptors
This Flowmaster (615157) Delta Force Cold Air Intake System will give your F-150 up to a 15% increase in both horsepower and torque! This intake system features a custom-molded high-flow intake tube, aircraft-quality black anodized aluminum fittings, high-quality reinforced silicone couplers and stainless steel hardware. Even better? It also comes with a serviceable lifetime conical shaped 8-layer cotton gauze air filter that traps more dirt than a typical 6-panel design! You’ll also get a custom-fit air dam that has attachment brackets to keep it securely mounted to the system. Easy to install, this cold air intake won’t require any drilling or cutting to put it on your pick-up and no tuning will be necessary either. The entire system is proudly made in the USA!
*For maximum performance and that iconic Flowmaster exhaust tone, we highly recommend pairing your new Delta Force Cold Air Intake with a Flowmaster Exhaust System.
Order a Flowmaster (615157) Delta Force Cold Air Intake System for your 2017-2018 3.5L EcoBoost F-150 or F-150 Raptor from CJ Pony Parts today!
California Residents: Proposition 65 Warning
Related Categories: Ford F-150 Raptor Parts, Ford F-150 Parts, F-150 Engine, F-150 Raptor Engine, F-150 Cold Air Intakes
This item is 50-state legal (CARB E.O. Number D-698-7)
Installation Videos
Video Transcript
Cold air intakes are one of the easiest ways to improve the performance and efficiency of your vehicle. So, today we're going to be installing this Flow Master Delta Force Cold Air Intake on our 2017 F-150 Raptor.
This Flow Master Cold Air Intake is a must have for your Raptor if you're looking for an affordable way to make it breathe better for improved performance. It was made right here in the USA, and features a single piece high flow polyethylene intake tube with a massive pre-oiled intake air filter protected by a powder coated heat shield. It comes with everything you need for an easy install, so today we're going to install it on our 2017 F-150 Raptor.
Tools you'll need for this installation: 7mm Socket, 8mm socket, 1/4 inch ratchet, 5/32 hex key, 3/8 ratchet, and a pair of cutters.
This intake is pretty simple to install. The first thing we're going to do is remove the factory one. First thing we're going to do is pop off the clips on the factory air box. Then loosen this clamp with a 17mm socket. And then this clamp down here as well. To loosen this clamp, the head of the screw is on the other side, it's kind of hard to see, but it's just on the other side of this tube. With both clamps loosened, you can now remove the entire intake. Unplug this intake sensor. Then remove the filter.
We can begin to assemble our new intake starting with the velocity stack, and the heat shield. Line the stack up with the holes on the heat shield, and install the provided screws. The rubber trim can then be installed onto the heat shield. Firmly press it into place. Once you get it in place, you can trim off the excess. Flip the heat shield over, and then on all four edges, install the provided sticky foam.
The air filter can then be installed onto the velocity stack. Grab your Delta Force intake tube and install the provided grommet. Remove the factory intake sensor from the intake by twisting it and pulling it out. Lubricate the grommet with a little bit of WD40. Now install the intake sensor into the grommet. You want this locking tab on the sensor to be facing the air filter. Install the couplers and clamps onto the intake tube. This can now go on the vehicle.
Slide the couplers over the factory intake tubes, then the air filter, and then the coupler. Everything is in place, you can now tighten all the clamps. Get the tube clips on the air box. Don't forget to plug in your intake sensor. Then your installation is finished.
Okay, we've got our Flow Master Delta Force Cold Air Intake installed. I'm loving the way it looks. It should help our truck to breathe a lot better, and you'll hear those nice induction noises when you rev it up. Install is not too bad either, it's only going to take you about an hour. And before you know it, you'll be heading off road.
