Glass Kit Complete Fastback 1965-1966

CJ's Part Number: WGK2-V
MSRP: $980.55

CJ's Low Price: $930.99

1508630400 43400
Earn 930 RPM Points What's this?
Glass Kit Complete Fastback 1965-1966
Glass Kit Complete Fastback 1965-1966 Glass Kit Complete Fastback 1965-1966 Glass Kit Complete Fastback 1965-1966 Glass Kit Complete Fastback 1965-1966 Play Glass Kit Complete Fastback 1965-1966 Video 1

Product Description

Complete Glass Kit for 1965-1966 Mustang Fastbacks.

Give your Mustang all new, crystal clear glass, with this complete glass kit! Available in clear, smoked or tinted glass. To tell which style you have, place a sheet of white paper behind your glass. If it is still white, you have a clear glass. If the paper has a green tint, then you have tinted glass. Smoked glass is an aftermarket option. Be sure to install new seals when installing new glass.

-Both vent windows
-Both door glass
-Rear window

*All glass kit options include a tinted glass windshield.
*Smoked glass is 32% tint.

Similar Mustang Parts

similar Mustang parts More Glass  

Installation Instructions

Mustang Installation

Mustang Applications

This product will fit the following Mustang years:

Product Reviews

Write a review
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 130.55ms
  • bvseo-msg: HTTP status code of 404 was returned;

Product Questions

  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 129.72ms
  • bvseo-msg: HTTP status code of 404 was returned;

You Might Also Like

Product Video

Glass Kit Complete Fastback 1965-1966 Video Transcript
By Bill Tumas: We’re here with an update on our project 50-30. We’re two months away from SEMA. This will probably be one of the last updates where we can show you the entire car. We have a lot of manufacturer’s on board with this build, and we want to give you brand new products at the SEMA Show that aren’t available to the public, so we can’t show them to you until the car is debuted. Guarantee though, we will be there at the SEMA Show and we’re going to give you a full overview of this car, top to bottom, sitting on the floor at the Las Vegas Convention Center. For now we’ll give you a couple updates on what we’ve been doing.

For our first update we’ll go under the hood, and if you’ve been following the build you know we were talking about reusing Ford Racing’s Coyote Crate engine to power our car. Four hundred twelve horsepower would have been great, but if you remember I said we were going to make it a little be more than that with Project 50-30. Additional power is going to come from a Vortex supercharger. We’re using their block series V3 supercharger to reliably push our car over 600 horsepower. This will work great with the stock motor and the factory computer we’re using.

We also recently installed the front windshield and the rear glass. We’re using one of our glass kits which is available for all ’64-’73 Mustangs, including all the glass necessary for the restoration. They’re available in clear or the tinted smoke glass shown here. If you go with the smoked, only the very top edge of your windshield is going to be smoked. The rest will be clear. We think the tinted glass is going to give our Mustang a really nice custom look with our black roof.

While not necessarily exciting to look at, our last update is going to be the wiring harness. With a custom build like this, having a good harness is going to be very important to make everything operate properly. We’ve chosen to go with Painless Performance Products complete chassis harness, fitting your ’64-’66 Mustang. Two additional models are also available fitting ’67-’68 as well as ’69-’70. The Painless will update 50-30 to modern wiring, giving us plenty of extra circuits to hook up with our control pack as well as all the extra power options we’re adding to our build.

Like we said before, we can’t show you everything, and we still have a ton of cool stuff to show you on our project 50-30, so make sure you subscribe to our YouTube channel for more updates.