KC HiLiTES LED Under Hood Lighting Kit V2 Cyclone 2-Piece White

100% of 100


  • Universal Fitment
  • Includes 2 Cyclone Lights
  • IP68 Weatherproof Rating
  • Wiring Harness W/Switch
MSRP $90.49
You save $0.50

KC HiLiTES White 2-Piece Cyclone V2 LED Under Hood Lighting Kit.

Light up your vehicle's engine compartment with this White 2-Piece Cyclone LED Under Hood Lighting Kit from KC HiLiTES. This kit will illuminate your engine bay with very little AMP draw. The universal LED light kit is simple and straightforward to mount!

Features and Benefits:
- Universal under hood mounting package included
- One Cyclone V2 puts out 600 RAW lumens of light for vibrant visibility
- Package includes all necessary wiring
- IP68 rated waterproof sealing
- Cyclone LED lights feature extremely low amp draw and high output in a compact package

This pair of bright Cyclone LED lights features die-cast aluminum housings with centrally located universal mounting holes. The multi-functional, compact design delivers 600 lumens of LED output for visibility in your once dark engine bay. A V2 LED comes as a flood beam pattern for vertical and horizontal beam patterns. 

- Raw lumens: 600lm (EA)
- Wattage: 5W
- Voltage: 9V-16V
- IP Rating: IP68
- Diameter: - 2.20” x Depth - 0.53"

- (2) Cyclone V2 LED lights
- Wiring
- Weatherproof switch
- Mounting hardware

California Residents: Proposition 65 Warning

Installation Difficulty


Novice skill is required for this installation.

Installation Videos

Video Transcript

When working under the hood of our Jeep, especially at night and even sometimes in the studio, it can be hard to see. Today we're gonna make it a little bit easier to work under the hood by installing this KC Cyclone under hood light kit.

This kit comes with two super bright Cyclone LED lights that we'll mount under the hood to make it easier when working under the hood, and it comes with its own wiring harness for an easy installation. Today, we're gonna install it on our 2016 Jeep Wrangler.

Tools you'll need for this installation, 3/8" ratchet, 10mm socket, a tape measure, marker, a drill, 1/8" drill bit, Phillips head screwdriver, and safety glasses.

This kit comes with two lights which you can mount anywhere under the hood. You want to find some place that'll light up the whole entire area evenly. We're gonna mount ours five inches above the sprayer nozzle on each side, and that should light up the whole underside of the hood pretty evenly.

We're gonna mark up our holes before we do any drilling. That'll be five inches above the washer nozzle. We're gonna drill out the holes with an 1/8" drill bit, and you might want to put some tape around the drill bit, just so you don't shoot through the metal and go through the other side of the hood. You don't want to damage the other side.

It's time to install the lights. Put the nylon washer in the center of the light, then put the screw through it, then you can screw the light into the hole you just drilled. There we go.

This kit does come with its own wiring harness, so we're gonna run the wires up through this portion of the hood to this light, and then run it across to the next light, and then connect it to the battery. Once you get the wire to the light, connect the black wire to the black wire, and the red wire to the red wire. Now we can run the wire to the other light. This one should be a lot easier.

We're gonna loosen up the nut on the stud of the negative battery terminal, and then we're gonna remove the negative battery terminal. Set that aside, and then go over to the positive terminal. Loosen the nut on the stud on the positive terminal, then connect the red wire from the wiring harness to the stud. Reinstall the nut, and tighten it down. Then remove the nut from the stud on the negative terminal, place the black wire from the harness over the stud, and reinstall the nut and washer. Reinstall the negative terminal, and tighten it down.

Once you get everything connected, you can find a place to hide the wiring or mount the switch, and then you can test and see if it works.

Our KC under hood lights are installed. They're actually incredibly bright. They're really going to help out when you're working underneath the hood. Installation will take you about 45 minutes, and before you know it, you'll be heading off-road.

Vehicle Fitment

This product will fit the following Bronco years:

This product will fit the following C10 years:

This product will fit the following F-100 years:

  • 1948,
  • 1949,
  • 1950,
  • 1951,
  • 1952,
  • 1953,
  • 1954,
  • 1955,
  • 1956,
  • 1957,
  • 1958,
  • 1959,
  • 1960,
  • 1961,
  • 1962,
  • 1963,
  • 1964,
  • 1965,
  • 1966,
  • 1967,
  • 1968,
  • 1969,
  • 1970,
  • 1971,
  • 1972,
  • 1973,
  • 1974,
  • 1975,
  • 1976,
  • 1977,
  • 1978,
  • 1979,

This product will fit the following F-150 years:

This product will fit the following Gladiator years:

  • 2020,
  • 2021,
  • 2022,

This product will fit the following Ranger years:

  • 2019,
  • 2020,
  • 2021,
  • 2022,

This product will fit the following Super Duty years:

  • 1999,
  • 2000,
  • 2001,
  • 2002,
  • 2003,
  • 2004,
  • 2005,
  • 2006,
  • 2007,
  • 2008,
  • 2009,
  • 2010,
  • 2011,
  • 2012,
  • 2013,
  • 2014,
  • 2015,
  • 2016,
  • 2017,
  • 2018,
  • 2019,
  • 2020,
  • 2021,
  • 2022,

This product will fit the following Wrangler years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account