Idler Arm Assembly for all 1967, 1968, 1969 and 1970 Mustangs with Manual Steering.If you have noticed a decrease in ride quality and drastically increased tire wear, perhaps it is time to revamp and update the components of your 1967-1970 Mustang’s manual steering system. No one wants to ride in a noisy, bumpy and rough ride and a new idler arm assembly like this one can help eliminate those excessive vibrations you feel. This Idler Arm Assembly for all 1967, 1968, 1969 and 1970 Mustangs is a direct stock replacement that will help heighten the manual steering’s responsiveness and accuracy.
The idler arm attaches at the one end of the center link on the passenger’s side of the vehicle and this assembly comes with the bushings, hardware and mounting bracket included. The other side of the idler arm bolts directly to the vehicle's frame rail. Typically, the idler arm is attached on the opposite side of the center link from the pitman arm and the vehicle's frame which allows it to hold the center link at the proper height. This Idler Arm Assembly will fit any 1967-1970 Mustang with manual steering and comes ready to install directly in place of the stock arm with a straight forward, headache-free installation.
Idler arms generally break down and become unstable more quickly than pitman arms because of the pivot function that is built into them. It is a good idea to replace this component of your steering system because after years of use and stress, its integrity is likely compromised. A worn out idler arm can lead to poor ride quality, unpleasant vibrations and unpredictable, uneven steering abilities in your 1967, 1968, 1969 or 1970 Mustang.
*Mounting hardware is sold separately.
If the stock manual steering system in your Mustang has become less responsive, is malfunctioning completely or you just want to make a conversion from manual to power steering, or vice versa, CJ Pony Parts has got you covered. Ordering any of the more than 500 steering parts here at CJ Pony Parts for any year Mustang is so simple—you can order online right now or give the sales team a call any time to place your order!
Product ReviewsWrite a review
Idler Arm Assembly Manual Steering 1967-1970 is rated out of 5 by 5.
Rated 5 out of 5 by Texmjs from Great product The part went into place perfect, there is no need for grease like the factory one.
Date published: 2015-01-08
Rated 3 out of 5 by Abbazabba from Good fit. Usable Wish I knew it was made in Taiwan. I prefer American made.
Date published: 2015-05-01
Rated 5 out of 5 by Kiwi Ray from Borgeson 800111 change over Used it in my 67 Fastback to replace the old power steering setup with the Borgeson: 800111. My old power steering box was 1 inch shaft (I did not know this when I brought the gearbox) so i needed the center link plus the 1 1/8 Pitman arm plus the idler to complete the change over....it works super great now
Date published: 2015-05-06
Rated 1 out of 5 by EMendoza from Loose The idler arm did not fit properly on the center link, it is loose compared to the original idler arm.
Date published: 2016-03-18
Rated 5 out of 5 by Turtle1 from Great product Idle arm bolted right in. 20 mins old was out and new one in. No modifications needed
Date published: 2015-10-24
I have a 68 Mustang. I think it was power steering. Now a manual. How can I tell the difference between manual or power arm?
the hole in the center of mine was filed with dirt, thought i had the 2 hole one(it has 2 bolts) but its a 3 hole and just uses 2bolts
Date published: 2016-11-28
I have a 67 mustang that has power steering but the idler arm it has is the same as this one which is for manual steering ? confused on which one I should get
If the car has factory power steering use the power steering arm. If it had manual steering and a aftermarket power steering kit it will need a manual steering arm.Due to different manufacturers it may look different but still work the same.
Date published: 2016-08-01
Would this idler arm fit a 67 Fairlane with manual steering?
The vendor has not provided any information regarding cross-fitments of this part to any other model then what is listed.
Date published: 2016-06-16
Hi, Do I really get the 2-piece OE style Manual Steer Idler Arm like shown on the pictures if I order this one?
Yes, it comes as pictured.
Date published: 2015-04-20
Will this idler arm fit the 1969 & 1970 manual steering Boss 302?
It should fit.
Date published: 2015-03-30
You Might Also Like
/** * Cases for simple product that is not on sale */ ?>CJ's Low Price:$189.99