Ken Harrison Radio Speaker In-Dash Upgrade 1967-1968

Ken Harrison:
MU678
Ken Harrison Radio Speaker In-Dash Upgrade 1967-1968 is rated 2.7 out of 5 by 6.
  • y_2019, m_11, d_20, h_3
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.3-b1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_6
  • loc_en_US, sid_SPK06, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getAggregateRating, 174.88ms
  • REVIEWS, PRODUCT

Highlights

  • Center Dash Mounted Speaker
  • 2 Separate 3-1/2" Drivers
  • For Use With Modern Radios
  • Direct-Fit Replacement
$46.99

Ken Harrison In-Dash Upgraded Radio Speaker for 1967-1968 Mustangs.

When it comes to the audio system in your Classic Mustang, most owners want a simple set-up but some owners want to upgrade for a better sound quality. Replace you’re worn out in-dash speaker with this high quality upgrade from Ken Harrison. This in-dash speaker fits in the dash on all 1967-1968 Mustangs that have upgraded the radio to a modern unit.

Ken Harrison In-Dash Speaker Features:
- 2 X 3.5" Coaxial 2 way speakers
- High Quality Paper Cone
- 25 oz. Magnet / 50 oz. Magnet Structure
- 1" Mylar Tweeter
- 1" Hi-Temp Voice Coils
- 140W MAX / 80W RMS
- Efficiency: 86dB (1W/1M)

Please Note: This in-dash speaker does NOT include speaker wire for installation.
Vehicle Fitment Note:
This in-dash speaker will also work on 1967-1968 Cougars.

The in-dash speaker has two separate 3-1/2" speakers that can be finely tuned for the perfect sounding system. The speaker cone is made out of a high quality paper which helps with the sound travel. This speaker also features a 1" tweeter that helps with the high-frequency noise. This little speaker can pack a big punch with its ability to push out 86dB which is adequate for this small speaker.

*This is one (1) individual speaker.

If you are a Mustang owner that is looking to repair or replace the original radio equipment in your classic Mustang, then CJ Pony Parts has exactly what you are looking for with our inventory of Ken Harrison radio equipment and accessories. Ken Harrison is a Mustang industry leader in the production of authentic appearance radio bezels, surrounds and speaker systems, as well as full radio assemblies with modern face plates to bring all of the power and technological advancements of a modern radio in your classic Mustang.

Purchase a new Ken Harrison In-Dash Upgraded Radio Speaker for 1967-1968 Mustangs from CJ Pony Parts today!

Vehicle Fitment

This product will fit the following Mustang years:

Rated 1 out of 5 by from Doesn't fit my '67 Working on restoring my '67 and was excited to install the speaker in my dash today as there wasn't one there at all. Made all of the preparations only to find that the mounting holes in the speaker are 11" apart and the mounting studs under the dash are only 7.5" apart. Very disappointing...Definitely check measurements AND ask questions before you buy this.
Date published: 2015-10-17
Rated 5 out of 5 by from Fits and works great! Just installed this in my '68 coupe, its easier to install with the radio bezel out, the secret is that it mounts to both inner defroster duct screws, you have to remove the original speaker studs in order for it to fit.
Date published: 2016-07-08
Rated 1 out of 5 by from did not fit standard 67 Mustang mounting location This speakers mounting holes are 11" apart, the standard Mustang dash speaker mounting holes are 7 1/2" apart. This speaker could be adapted to the defroster vent mounting holes with a bit of work but it was listed as fitting 67-68 Mustangs and it does not.
Date published: 2019-07-20
Rated 2 out of 5 by from Does not fit This speaker setup looks good, but is too wide to fit on the studs for the stock speaker, I had to remove them and mount the speaker on the studs for the defroster ducts. Even then, the outer contour of the speaker did not fit the contour of the dash.
Date published: 2017-03-02
Rated 5 out of 5 by from 1967 Mustang Front Speaker Good stereo speaker for the money & good fit on a non-AC car! Mounts to the defroster studs which are 11" center to center!
Date published: 2017-04-10
Rated 2 out of 5 by from Mounting holes did not match existing hardware I made it fit , speaker quality not the best faded sound mostly to rear speakers
Date published: 2016-10-07
  • y_2019, m_11, d_20, h_3
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.3-b1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_6
  • loc_en_US, sid_SPK06, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getReviews, 3.45ms
  • REVIEWS, PRODUCT
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 115.54ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;