Sequential Hood Light Kit 1967-1970

CJ's Part Number: HDTSS3

Regular Price: $54.99

Special Price: $43.99

1477526400 17247
Add this part to go along with your new light kit!
CJ's Low Price:
Earn 43 RPM Points What's this?
1477353600 1477526400
On Sale: Sheet Metal Sale!
Sequential Hood Light Kit 1967-1970
Sequential Hood Light Kit 1967-1970 Play Sequential Hood Light Kit 1967-1970 Video 1

Product Description

Sequential Hood Light Kit for 1967, 1968, 1969 and 1970 Mustangs.

Is the hood on your 1967-1970 Mustang equipped with turn signals? If so, replace the old and dim turn signal hood light bulbs with this Sequential Hood Light Kit from CJ Pony Parts!

This Sequential Hood Light Kit comes with 4 sets of bright amber-colored LED lights that are much brighter than your factory lights, even in direct sunlight! You can use your existing wiring and housings for easy plug-and-play installation. You don't even have to worry about re-doing any complicated wiring to install this kit either! This kit comes with two LED modules that are direct fit replacements and are marked left and right to make putting them in even simpler. This Sequential Hood Light Kit is an excellent upgrade for any 1967-1970 Mustang with a hood that has provisions for turn signals.

If you're doing a restomod or even a concours restoration to your classic Mustang, one option that is available is hood turn signals. These parts add a unique element to Mustangs and are something that few other cars offer. If you want to add this unique element, or repair broken parts, check out the line of Mustang Hood Turn Signal Lights available from CJ Pony Parts!

Order a Sequential Hood Light Kit for your 1967, 1968, 1969 or 1970 Mustang from CJ Pony Parts today!

Similar Mustang Parts

similar Mustang parts More Hood Turn Signal Lights  

Installation Instructions

Mustang Installation

Mustang Applications

This product will fit the following Ford Mustang years:

Product Reviews

Write a review
Sequential Hood Light Kit 1967-1970 is rated 3.6666666666666665 out of 5 by 6.
Rated 1 out of 5 by from Ripped out and sent to the trashcan Where to begin. These are simply poor quality in design and execution. The instructions are terrible. Not that they're really needed because of the simplicity but they're bad-photocopied, unproofread and/or written by someone who didn't really speak english. The lights do function. in that they light up but that's where the likability ends. If your underhood already looks like a can of silly string exploded or if you're wiring them into a car that originally didn't have the turn-signal hood then maybe you're cool with it. I was not happy after installing one so good thing I didn't cut off the original light socket as the instructions suggest. You have to apply an included foam tape over the back of the circuit board to protect it. This isn't optional so why is the foam not applied from the start? Also, it doesn't mount anywhere, it's just kind of stuffed in the hole. They aren't made with SMD-LED's either, so they're much thicker then required for the design. Due to this thickness and lack of mounting, you can forget about good alignment, the lights will be slightly off-kilter both in the hood and differently from each-other. The original hole for the lamp socket is left unsealed so water/moisture can easily get up in the housing. Then you're left with a lot of electrical tape required to make the wiring look OK (and forget it if you don't want to cut off the original lamp-sockets). I did one and was so overwhelmed with a desire to dump last night's spaghetti all over the engine that I ripped it out and tossed them. If you care about how it looks under there, don't go near them.
Date published: 2015-07-08
Rated 5 out of 5 by from WoW! Ordered these signals to give my 69 a bit of pop. I am finally down to the details on it. I want to make all the lights I can LED. These signals are very nice, easy to install into the original bezel. Of course, I had to remove the scoop to install them, but that's just the way it is! I did not realize they were sequential until I clipped them in and turned on the blinker. Be sure to test electricals BEFORE you finish the install! Very nice! Thanks CJ PP!
Date published: 2015-01-22
Rated 5 out of 5 by from The sequential turn signal indicators look great! I recently purchased the sequential turn signals for my 1970 Mach 1. Adding these sequential hood indicators was just icing on the cake. They are brighter than the original indicators so can be easily seen on the brightest day. Love them.
Date published: 2015-06-18
Rated 3 out of 5 by from They're ok These are bright and work well, however I don't like how makeshift it made my engine compartment look. I actually switched these out with the Scott drake sequential and am happier for it. I will say I had not issues functionally I just couldn't take the unprofessional look of it.
Date published: 2015-05-06
Rated 4 out of 5 by from the lights work very well I bought these lights for fun. They are very bright during the day which is what I wanted because the incandescent bulbs were too dull.
Date published: 2016-03-04
Rated 4 out of 5 by from Sequential hoodlight kit Works great, but the hookup for the wires was a mess.I modified the factory wires and concealed the hookup.
Date published: 2016-09-17
  • 2016-10-27T07:58CST
  • bvseo_cps, prod_bvrr, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_6
  • loc_en_US, sid_HDTSS3, PRD, sort_relevancy
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 154.79ms

Product Questions

Is this with or without lens?

Asked by: Tommyas
No lenses are included - use your existing!
Answered by: CJ Pony Parts
Date published: 2015-06-05

Does it come with the wire harness for the lights

Asked by: Wilson1967
  • 2016-10-27T08:16CST
  • bvseo_cps, prod_bvqa, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_2
  • loc_en_US, sid_HDTSS3, PRD, sort_recentAnswersFirst
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 159.56ms

You Might Also Like