Borla Axle-Back Exhaust System Stainless Steel 2-1/4" ATAK V6 2011-2014
- Stainless Steel Construction
- 2-1/4" Mandrel Bent Tubing
- Made In The USA
- 4-1/2" Rolled Exhaust Tips
Borla Stainless Steel 2-1/4" ATAK Axle-Back Exhaust System for all 2011, 2012, 2013 and 2014 V6 Mustangs.
If you are looking to add the most aggressive axle-back to your 2011-2014 V6 Mustang, the Borla ATAK axle-back is by far the perfect choice! Borla’s patented ATAK technology, stands for Acoustically-Tuned Applied Kinetics, and produces the highest available decibel levels in the Borla street-legal lineup while retaining clarity of sound and avoiding distortion.
Borla axle-back exhaust systems feature patented, straight-through and multi-core technology to unleash hidden horsepower. Ultra-smooth 2-1/4” mandrel bent piping ensure maximum flow and power and every system is constructed from premium austenitic aircraft-quality 300-series stainless steel to give you the absolute best performance and durability. Fit and finish is perfect thanks to precision computer-controlled CNC manufacturing. All this leads up to a set of 4-1/2" x 10" round, rolled, angle cut, Borla embossed tips that exit the rear of the vehicle.
Features and Benefits:
- Made in the USA
- Full 300-Series Stainless Steel Construction
- Easy to Install, Direct Bolt-on
- Highest Available Street Legal Decibel Level
- Incredible Sound Clarity with No Distortion
- Straight-Through Multi-Core Design
- Borla Embossed 4-1/2” Round, Rolled and Angle Cut Tips
*Fits ALL 2011-2014 Coupe and Convertible V6 Mustangs.
The factory exhaust is frequently the first item to get replaced in any new or classic Mustang restoration, and rightly so. The increased performance and better sound that you'll get from an aftermarket system usually far exceeds what the factory can offer. The products from Borla Performance Industries are some of the top exhaust systems available for your Mustang on the market.
Order the Borla ATAK 2-1/4" Stainless Steel Axle-Back Exhaust System for your 2011, 2012, 2013 or 2014 V6 Mustang from CJ Pony Parts today!
California Residents: Proposition 65 Warning
Novice skill is required for this installation.
Everything about the Borla Atak is aggressive, from the tone down to the massive four inch rolled polish tips. The whole system is stainless steel. It's a direct replacement for your factory mufflers.
We'll give you a quick before clip of the stock exhaust. Our '13 is a bone stock Automatic GT. Definitely not a bad exhaust system for a stock, but an aftermarket is definitely going to sound a lot better.
For this installation, you'll need jack and jack stands or a lift, 3/8 ratchet, 15mm socket, 13mm socket, exhaust donut removal tool, small pry bar, hammer, snips, and safety glasses.
You'll see the mufflers are located right here in the back of the car and they're held under the tail pipes by one clamp, so there's one bolt to remove. Now, we're going to work on removing it from the hanger. It's a good idea to put a towel of some sort over the tip so you don't damage your factory bumper.
Once we have it off the rear hanger, we're going to disconnect our tail pipe from our H pipe. This isn't necessary to do this. You can actually fight your way off the back, but removing this is a lot faster and it's a lot easier. Once we get that loose, we can actually just let it hang here out of the way. Now, we'll slide it forward off the front hangers. I'll spray a little lubricant into the hangers before we install our new exhaust.
The Atak requires you to reuse your original clamps. They're going to come off with your mufflers. If you look, there's a small tack actually holding them on. Using a small pry bar or a screwdriver and a hammer, you can break that right off. You'll want to put the towel back on the new muffler to protect the new tip, as well as, again, protecting the bumper. They are side specific and Borla labels it to make it easier.
Now we have the back two. We'll do the front one last. That's situated roughly where we want it and now, we can reinstall our tail pipe. First, we'll put the clamp up onto the muffler and now we'll grab our tail pipe. Now, we'll tighten up the H pipe to our tail pipes, and we'll tighten the muffler. You kind of want to center it on the rear hanger and we can hold it there while we tighten up our clamp and our installation's finished.
Let's fire it up and see how our Borla Atak sounds. The Ataks give us a nice aggressive sound from our otherwise bone stock Mustang. Our Borla exhaust not only sounds aggressive, it looks aggressive too. Installation should only take you around an hour and you'll be back on the road in no time.