Corsa Resonator Delete X-Pipe 2-3/4" F-150 Raptor 2017-2020
Highlights
- 2-3/4" Mandrel Bent Tubing
- Flows 9.92% Better Than Stock
- No Welding Required
- Easy Installation
Corsa 2-3/4" X-Pipe Resonator Delete for 2017, 2018, 2019 and 2020 F-150 Raptors.
If you're looking for a way to get a deeper, louder and bolder exhaust note out of your 2017-2020 Raptor F-150, but you don't want to break the bank, CJ Pony Parts has the perfect solution for you: this Corsa 2-3/4" X-Pipe Resonator Delete!
Features and Benefits:
- Replaces Stock Resonators
- Increases Sound with a Crossover Section that Creates a Unique Exhaust Note and Scavenges Airflow
- Full 2-3/4"-Diameter Pipe Maintains Appropriate Frame Clearances
- Flows 9.92% Better than Stock
- 8 Lbs. Lighter than Stock
- Easy to Install: No Welding Required
- Direct Bolt-On Installation: Easy Addition to Stock Exhaust, Corsa Muffler Upgrade or Corsa Cat-Back Exhaust
- Fits 2017-2020 F-150 Raptors with a Super Cab and SuperCrew Cab
This Corsa (14396) 2-3/4" X-Pipe Resonator Delete is a great way to replace your stock resonator, and it's also a great addition to your stock exhaust, your Corsa muffler upgrade or your Corsa cat-back exhaust. It will increase the sound you hear with a crossover section that creates a unique-sounding exhaust note and scavenges airflow. The full 2-3/4"-diameter pipe will maintain the appropriate frame clearances too. This Corsa X-Pipe Resonator Delete flows 9.92% better than stock, and it's also 8 lbs. lighter than stock! Easy to install, this X-Pipe Resonator Delete won't require any welding to put on your Raptor. You'll love hearing your louder and more aggressive F-150 after you're done!
California Residents: Proposition 65 Warning
Related Categories: Ford F-150 Raptor Parts, Ford F-150 Parts, F-150 Exhaust, F-150 Raptor Exhaust, F-150 Resonator Deletes
Installation Videos
Video Transcript
The new Raptor's a fantastic truck that makes a ton of power, but it's a bit too quiet. So today we're gonna make it sound a whole lot better by installing this Corsa X-Pipe Resonator Delete. This Corsa resonator delete is made of 2-3/4" mandrel bent stainless steel tubing that's designed to be a direct fit replacement for the factory resonator. It weights eight pounds less than the factory resonator and improves exhaust flow for better sound and performance. Today we're going to install it on our 2017 F-150 Raptor.
Tools you'll need for this installation: A lift or a jack and jack stands, 10mm socket, 13mm socket, 3/8" ratchet, 15mm socket, 1/2" ratchet, a 10mm wrench, 15mm wrench and you might need a hammer.
Okay. We have the truck up in the air and the first thing that we're going to do is remove the entire exhaust. We're going to loosen up all the clamps starting at the front of the exhaust and then just work our way back. Remove the two bolts on the front flange with a 13mm socket. Remove the two 10mm bolts holding on the bracket for each tailpipe. Finally, remove the two nuts on the bracket from the rear of the tailpipe. Remove the bracket. Then you can remove the tailpipes. These tailpipes can be a bit tricky to remove. You just gotta do a little bit of lifting, twisting and turning and they will come out.
And remove the other tailpipe. With the tailpipes off, you can remove the muffler assembly by pulling it towards the rear, sliding it out of the hangers. There's the muffler. Here's the last thing that needs to come off, the factory resonator. Here's a side by side comparison of the Corsa Resonator Delete and the factory resonator. The Corsa one's obviously going to flow a lot better and make this thing sound a whole lot better.
We're going to put our factory sleeve clamp back on this down part and then install the resonator delete. Install the factory bolt and the provided nut into the flange. Do the same thing for the other side of the flange. Tighten up the nuts and bolts with 13mm socket or wrench. Tighten the two 15mm nuts on the sleeve clamp. We'll slide a clamp over each side of the resonator delete. Then your extension pipes. Next, you can install your muffler assembly. With the muffler installed, you can install both tailpipes now. Just takes a little bit of twisting and you can get them in there. Then reinstall all your brackets for the tailpipes.
Install the other tailpipe. Once you get the whole exhaust put together and all the brackets installed, you can go back and tighten all the clamps. We are done. All right. Time to hear how it sounds. All right. Our Corsa Resonator Delete is installed on our Raptor. It's definitely a good bang for your buck upgrade. It gives our Raptor a bit more of an aggressive tone. It makes it a little bit louder but it's not too extreme and it's not going to wake your neighbors when you start it up. Installation is pretty straight forward. It's probably going to take you about two hours to install. And before you know it, you'll be heading off road.
