Flowmaster X-Pipe Kit Scavenger 3" Stainless Steel GT 2011-2014

Flowmaster:
81106
Rating:
100% of 100

Highlights

  • Made In The USA
  • Direct Bolt In Design
  • Stainless Steel Construction
  • No Tuning Required
MSRP $390.00
$350.95
You save 10%

Flowmaster 3" Stainless Steel Scavenger X-Pipe Kit for 2011, 2012, 2013 and 2014 GT Mustangs.

Are you looking to boost the roar of your 2011-2014 5.0L GT Mustang, than you'll definitely want to order this Flowmaster 3" Stainless Steel Scavenger X-Pipe Kit (81106) from CJ Pony Parts today!

Scavenger X-Pipe Features:
- Dyno Tuned For Maximum Performance
- Stainless Steel Construction
- High Quality 3” Mandrel Bent Tubing
- Direct Bolt-In Design
- No Tuning Required
- Made in the U.S.A.

*Does not remove or replace the catalytic convertors.

This direct-fit upgraded mid-pipe is a great way to change and improve the exhaust noise and sound level of your GT Mustang! Flowmaster's Scavenger x-pipe can be used on cat-back or axle-back exhaust systems and is manufactured from high-quality stainless steel. The 3" mandrel-bent tubing will help increase the overall sound of your pony's exhaust system, giving you an aggressively loud roar. What are you waiting for? Grab your new x-pipe from CJ's now!

Please Note: This X-Pipe Kit is NOT designed for use with the 2012-2013 Boss 302 due to the factory side exit exhaust pipes.

When you're looking for an exhaust for your 1964-2017 Mustang, every owner needs to check out Flowmaster's exhaust systems and mufflers. Flowmaster is a manufacturer of just about any part you need for your Mustang's exhaust, from full exhaust systems and exhaust kits to mufflers and accessories.

Order this upgraded Flowmaster (81106) 3" Stainless Steel Scavenger X-Pipe Kit for your 2011, 2012, 2013 or 2014 GT Mustang today from CJ Pony Parts!

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

The X pipe versus H pipe debate's never going to end, but today we're gonna get some ammunition to the X pipe side by installing a Flowmaster Scavenger X pipe on this 2012 Mustang GT.

This Flowmaster Scavenger X pipe is made of mandrel bend stainless steel right here in the USA. It will be a direct replacement for the factory mid pipe on your 2011 to 2014 Mustang GT.

For this installation, you'll need a lift or a jack and jack stands, 1/4" ratchet, E8 socket, 3/8 ratchet, 13 millimeter socket and a 5 millimeter socket.

We're gonna start by loosening these two clamps up front here to connect the converters to the rest of the factory mid pipe. Now these are a 13 millimeter up on top. They're hard to get to. If you have a set of reverse torque sockets though, the E8 fits perfectly on the bottom, makes it much easier.

With those loose, we'll move back to these clamps in the rear.

What you'll be able to do is basically slide this back, spacial clamps will be loose enough. It'll come off in the front.

These are our stock pipe endings here for our Flowmaster Scavenger X, obviously a much larger pipe, much better bends, much smoother flow. What we're gonna do now though is take the hardware from the factory pipe, transfer it over to the Flowmaster. On the clamps, there's gonna be a little stop. So you want to lift up on this with your finger then slide it off.

Now the front clamps are actually spot welded on. There's a couple things you can do here. If you have a cut off wheel handy, you can buzz right here and pop it off. But honestly, you can actually just work this off the end. Just twist it a couple times with your hand and usually, it'll snap off.

All right, now we're ready to put our Scavenger X up into place.

Once we get it into place, we'll start by tightening down the front clamps.

And make sure these clamps will wind up back here and tighten this down as well.

Go back through and make sure everything's tight. Make sure your tips for your exhaust are still even and straight and your installation's finished.

Now before I fire up, I'm gonna mention this car does already have a Roush axle back. Being how popular the Roush is, we're sure you know what that sounded like already. Let's hear what it sounds like with our Flowmaster X pipe.

It definitely kept the same kind of tone, but a little more volume and definitely over 4,000 RPM. You can really hear a difference.

The Flowmaster Scavenger X pipe's not only gonna flow a little bit better than the factory pipe. It's gonna be a little bit louder and more rowdy as well. As far as the installation goes, like you saw, it's a direct replacement, very easy to install, no more than about an hour. You'll be back on the road in no time.

Vehicle Fitment

This product will fit the following Mustang years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.