Ignition Switch Assembly Mustang 1965-1966

CJ's Part Number:
94% of 100


  • Direct-Fit Replacement
  • Correct Terminal Locations
  • Includes Spring
  • High Quality Construction
MSRP $19.99
You save 22%

Ignition Switch Assembly for all 1965-1966 Mustangs.

This all new, reproduction Ignition Switch Assembly is a direct fit replacement for the faulty original ignition switch in your 1965-1966 Mustang. If you are repeatedly having trouble with the ignition switch cylinder falling to the off position after starts, you may be able to fix that problem with this replacement Ignition Switch Assembly.

This quality Ignition Switch Assembly is one of the best reproductions available on the market today. You can replace an old, faulty or broken ignition switch with this new assembly and be confident your Mustang's ignition switch cylinder won't slip to the off position unwillingly again.

*Does not include a bezel, switch cylinder or ignition keys.

Additional Fitment:
- 1966-1977 Ford Broncos
- 1965 Mercury Comet
- 1960-1965 Ford Fairlanes
- 1960-1965 Ford Falcons
- 1960-1964 Ford Galaxies
- 1961-1964 Ford Thunderbirds

CJ Pony Parts has hundreds of Mustang components for all year Mustangs and nearly every aspect of replacement, tuning or upgrading available for you to order today. So check us out online, call us anytime or stop by the showroom and place your order today!

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

If you're having random starting issues or sometimes your Mustang just shuts off while you're driving, the ignition switch might be the culprit. This part can be rather intimidating to install, so we're going to show you step by step how to replace the switch using this Scott Drake piece and our Weekend Wrench project car.

The first step in installing a new ignition switch is to remove your lock cylinder. You'll just need the ignition key and a small pick to do so. The first step is to turn your key to the accessory position. You'll want to drive a small pick in the tiny little hole right below the key. You're going to press that in and then you're going to turn it counter clockwise past accessory and you can pull it straight out. Once you remove the key and the lock cylinder, make sure you're careful not to turn it at all. You want to leave it exactly the same way it was and it'll make it much easier to put it back in the car. Now we have to separate the ignition switch from the ignition bezel itself; to do that, we're going to have to go underneath the dashboard. You'll want to reach up behind and grab the back of the ignition switch.

The ignition switch is held into the bezel by a spring. You want to push in and turn counterclockwise to release it. It'll release and the bezel will pop out and you can fish the ignition switch underneath the dash. Now I'll remove the retaining nut from the back of the switch, the wire off the top, and then I'm going to remove the plug. A small screwdriver will help you separate it. The rubber plug seals tightly and sometimes it can be a little tough to get off. Now we're going to plug in our new switch. We have to reconnect the wire to the top, install our spacer onto our new switch, and now we're going to fish the switch back up into the dash. This is probably one of the most difficult parts of the installation. It's going to be hard to see as we do it so we're going to show you the pieces outside of the car.

Basically once you have the spacer installed the bezel is going to go to the dashboard itself, the switch is going to come in from the back. You're going to put it in and turn to lock it in place. Then you want to line the bezel up with the two tabs in the dash. Once it locks into place you push your new switch in and turn.

We're going to reinstall the key at the same angle we took it out and it'll wind up just past accessory. Pop it into place and then we turn. Once you reconnect your battery you can test out your switch and see everything is working like it's supposed to. The hardest part is getting the bezel to line up with the switch itself. Besides that the whole installation should only take you between 45 minutes to an hour, so you'll be back on the road in no time.

Vehicle Fitment

This product will fit the following Mustang years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.