JLT Cold Air Intake Kit Black Textured GT350/GT350R 2015-2020

JLT Performance:


  • Black Plastic Intake Tube
  • S&B Powerstack 5X7" Filter
  • Requires A Custom Tune
  • Made In The USA

JLT Performance Black Textured Cold Air Intake Kit for all 2015, 2016, 2017, 2018, 2019 and 2020 Shelby GT350 and GT350R Mustangs.

JLT Performance has invested a massive amount of hard work into getting this Cold Air Intake (P/N CAI-GT350-15) ready for market and the results will leave 2015-2020 GT350 and GT350R owners believing that it is nothing short of amazing!

This Cold Air Intake Kit CAI-GT350-15 from JLT Performance is a great way to get more power and performance from your 2015-2020 Shelby GT350 or GT350R Mustang. This kit from JLT will replace your intake with a black textured finish Cold Air Intake which will look great under the hood of any GT350. JLT has designed this intake to bolt right on to your new Shelby with no permanent modifications. The fully roto-molded heat shield and included fresh air duct will keep inlet air temps as cool as possible and feed the large 5" filter. The inlet tube also measures 4.5" on the throttle body side in preparation for larger aftermarket throttle bodies.

Features and Benefits:
- Provides Incredible Gains Over Factory Intake
- Computer Designed to Optimize Space
- Standard OEM-Looking Black Textured Plastic
- Accommodates Larger Aftermarket Throttle Bodies
- Huge Filter with Screen to Straighten Air Flow
- Made in the USA

Kit Includes:
- JLT Plastic Intake Tube
- Silicone Reducer Coupler
- 5”x8” S&B Powerstack Air Filter
- Heat Shield with Duct and Weatherstrip
- Heavy Duty Clamps and all Needed Hardware
- Detailed Installation Instructions

*A custom tune is required with this intake (not included).
*Designed for the 2015-2020 Shelby GT350 and GT350R only, will not work with regular GT models.

Keep in mind that JLT Performance only uses the best air filters available. They have them made by S&B to their exacting specifications. S&B's air filters feature a tapered flange design and Powerstack filtered ends. With a huge 5” opening on the tube, JLT Performance needed a huge filter. The result is a gigantic 5”x8” air filter that includes a built-in screen to help straighten airflow as it passes the perfectly placed molded in MAF.

It’s time to unleash even more N/A Horsepower and Torque from that 5.2L Voodoo Powerplant, order the JLT Performance CAI-GT350-15 Black Textured Cold Air Intake Kit for your 2015, 2016, 2017, 2018, 2019 or 2020 Shelby GT350 or GT350R Mustang from CJ Pony parts today!

California Residents: Proposition 65 Warning

Note: This item is not CARB (California Air Resource Board) exempt and is not legal for sale or use in the state of California.

Installation Difficulty


Novice skill is required for this installation.

Installation Videos

Video Transcript

No matter how much horsepower your Mustang makes in stock form, most true enthusiasts at some point in time will be looking for some more. At 526 horsepower the 2016 GT 350 is the most powerful naturally aspirated engine ever offered in a Ford Mustang. Like any other Mustang, though a few well chosen bolt on modifications are going to bump that number up a little bit. One of the best ways over the years we've found to add horsepower is good quality cold air kit from JLT Performance. Today we're going to install one on this 2016 GT 350.

This JLT cold air intake kit is going to figure 2015-2016 GT 350 or GT 350R. Because JLT is adding a lot more air into the engine, it will require a custom tune when running this kit, which is also available here at CJ Pony Parts. The kit includes this high flow filer, air box, plastic molded tube, and all necessary hardware for installation. For this installation you're going to need a 1/4 inch ratchet, 7mm socket, 8mm socket, 10mm socket, a short extension, Philips head screwdriver, and a T20 torques bit.

We'll start by removing the factory cold air kit, which is very easy to do. You loosen the clamp here and remove both these fittings. Disconnect the mass air center, and unbolt if over the fender. Start by loosening the hose clamp. We'll push in this yellow tab here, slide that off, and lift the little gray tab up here, slide that out of the way. For the mass air sensor slide the red tab out of the bottom. Pull the sensor off and pull it off the studs. The last thing you'll remove is this bolt in the fender well. Now you can carefully remove the whole unit as one piece. Before we put it aside, we need a few pieces off the stock air box. The first and most important is going to be the mass air sensor. You'll also want to grab these 3 rubber bushings and this one down here has a metal insert in it. Just pull these out. Now we're done with the factory air box.

Now we're going to install the sensor in the JLT inlet using the supplied hardware. You want to make sure use the JLT hardware, don't try to use the original. Start with the small one on top here, and you can just sort of push it and twist it into place. Then the second one goes on the inside of the box here. The last one we're actually going to install on the car. Put this grommet down into place here in the factory opening, and then we can lower in our JLT box. We've already installed the bolt in here to hold this in place. Then we take the JLT supply duct, put it down inside the box here and then slide it over the factory duct.

Now we'll take the silicone coupler from the throttle body. Put that over there, we'll tighten that down. Now we're going to take the filter and tack it to the main inlet tube. Now we'll tack this to the coupler of the throttle body and down into the air box. Clamp in place and tighten it down as well. We're going to make both connections on the inlet tube. Lastly, reinstall the mass air sensor. Your installation is finished.

The JLT Performance cold air intake kit looks great under the hood of our Shelby. We've had such success with JLT in the past we have no doubt we'll see horsepower and torque out of it as well. Again, remember because we are changing the size of the inlet tube, you will need a custom tune before you drive your car. The installation of the intake is very easy, take you about 30 minutes, be back on the road in no time.

Vehicle Fitment

This product will fit the following Mustang years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.
Complete Your Package
Add to Cart