JLT Performance Ram Air Intake Kit Series 2 Black Textured Mustang GT 1996-2004

JLT Performance:
95% of 100


  • For 1996-2004 GT Mustangs
  • 8-12+ RWHP Gains Are Typical
  • Includes All Mounting Hardware
  • 4" ABS Plastic Tubing
MSRP $251.99
You save $2.99

JLT Performance Black Textured Series 2 Ram Air Intake Kit for 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003 and 2004 GT Mustangs.

The four-inch tubing with JLT Performance's Black Textured Series 2 Ram Air Intake Kit RAI2-FMG-9604 is roto-molded and made of ABS plastic to produce a cold charge to your 1996-2004 GT Mustang's engine. By getting rid of metal tubing you can potentially gain 8-12 RWHP.


Kit Includes:
-JLT plastic intake tube
-Silicone reducer at the throttle body
-Silicone reducer at the MAF
-ABS heat shield
-4x9 S&B Powerstack air filter
-MAF adapter and gasket
-Heavy-duty clamps and all necessary hardware

JLT Performance started from scratch and optimized the flow to support your engine's performance. The all-new heat shield is vacuum-formed with ABS plastic and designed to block heat at low speed and idle.

Please Note: Will NOT fit with Kenne Bell supercharger.

California Residents: Proposition 65 Warning

This item is 50-state legal (CARB E.O. Number D-761-2)

Installation Difficulty


Novice skill is required for this installation.

Installation Videos

Video Transcript

A Cold Air Kit is a tried and true way to add house power to your late model Mustang. JLT Performance is one of the industry leaders in this category with Cold Air kits from everything from Fox Body Mustangs, up to your latest 2014 models. In most cases they offer two versions: the original True Cold Air, which puts the filter down in the fender for cold air charge, and this kit shown here, the Ram Air Kit, keeps everything under the hood for much easier installation.

Today, we're going to show you how to install the Ram Air Kit using our 2002 Mustang GT. This kit will fit 1996 to 2004 Mustang GT. It includes a heat shield for the air filter, reusable filter assembly, plastic textured inlet tube, detailed instructions, mass air adaptor, and all necessary couplers and clamps for installation.

The kit includes this grommet for the 1996 through mid 2001 Mustangs and a factory intake air temperature sensory mounted in the factory intake. If you do have that year model, you will drill a hole in the bottom of the plastic tube, install that grommet and that is where you install your factor IAT sensor. For this installation, you need 1/4" ratchet, 5/16 socket, 10 mm socket, 11 mm socket and a short extension.

Our '02 GT is bone stock making a perfect candidate for Cold Air Kit. The 2005 and newer will require a reflash of your computer when adding a Cold Air Kit, the older ones do not, so you can install it without any other changes necessary.

The first step is to remove the stock intake and air box assembly. It's pretty straight forward. Loosen the clamp up here. Remove these two fittings. Disconnect our meter. Remove this one bolt here and we can pull the whole assembly out together. You want to make sure to hang on to this bolt, you will need it for your Cold Air Kit.

We need to reuse the mass air housing, so I want to separate it from the intake tube here, and remove these four bolts to separate from the air box. Our JLT Ram Air Intake can be mostly assembled on the bench. We are going to start by removing the screen from this stock mass air meter as you do not reuse it. I can install the JLT supplied gasket and the adaptor. The housing is plastic, so make sure you don't over tighten them, just get them snug. I will install the coupler to the meter, and now the meter to the intake tube. I will install the filter to the meter. Last step is the coupler for the throttle body to the inlet tube. And, it's ready to install.

Before we install the Cold Air Kit, you want to remove this plastic fitting from the PCV connection here, install the supplied rubber hose to the other fitting. Now we're ready to install. I want to start by tacking it to the throttle body. Connect the PVC hoses. Now plug the mass air sensor back in. We'll install our heat shield using the bolt from the original air box, and our installation is finished.

There you have it. JLTs Ram Air Intake Kit's approved way to add horse power to your Mustang, and as you see, it's very simple to install. It shouldn't take you more than 1/2 an hour and you'll be back on the road in no time.

Vehicle Fitment

This product will fit the following Mustang years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.
Complete Your Package
Add to Cart