Power Window Switch And Bezel Kit Mustang Coupe/ Hatchback 1987-1993

CJ's Part Number:
PWSBK1
Rating:
100% of 100

Highlights

  • Complete Kit!
  • Includes Hardware
  • Quality Reproductions
  • Bold White Text
MSRP $141.49
$120.27
You save 15%

Power Window Switch and Bezel Kit for 1987, 1988, 1989, 1990, 1991, 1992 and 1993 Coupe and Hatchback Mustangs.

If your power window will not go up or down, the power window switch is typically the problem. Using this Power Window Switch and Bezel Kit from CJ Pony Parts to update your 1987-1993 Coupe or Hatchback Mustang's interior has never been easier!

Features and Benefits:
- Complete kit
- Easy to remove and replace original parts
- Includes installation hardware
- Quality reproductions
- Bold white text

This Power Window Switch and Bezel Kit will bring new life to your Mustang's door panels! The switches and bezels tend to have faded text and can sometimes be broken making your interior look old and worn. This kit addresses all the parts that can be replaced at the same time. Simply remove the driver and passenger side switch bezels and switches and replace them. Hardware is included to retain the switch bezels. These reproduction parts feature the same details as the original parts. Bold white text will give your Fox Body factory new looks.

Kit Includes:
- Three (3) power window switches
- Driver side power door lock switch
- Passenger side power door lock switch
- Driver side power window switch cover
- Passenger side power window switch cover
- Two (2) window switch cover screws

Vehicle Fitment:
- 1987-1993 Coupe/Hatchback Mustang

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

We have a lot of plans for the Black Pearl here on our 1990 Mustang project car. But, since I'm driving this car a lot lately, I'm working first on the things that are kind of annoying me. And one of them is the power window switches.

Right now I only have like two switches that work on this car, so to lock the door I have to actually reach over to the passenger side. So, I want to replace all the switches. And while I'm at it I'm going to replace the bezels, too by using this kit that'll fit your 1987 to 1993 hardtop mustang.

This power window switch and bezel kit's going to fit your 1987 through 1993 coupe or hatchback mustang. It's going to include all three power window switches along with two door lock switches, and all new bezels to give your car a fresher look and make it work properly.

For this installation, need a quarter inch ratchet, quarter inch socket, Phillips head screwdriver, and a small Flathead screwdriver. The process is the same for both sides, so we're going to show you the driver's side. This is actually a very easy installation. Any first timer can handle it. The first thing you're going to do, is remove this screw.

Before we get started, this is pretty much typical of what a lot of Fox body controls will look like. You can see the windows and doors. They're kind of almost worn completely off, as are all the controls. So the new controls will look a lot better, but most importantly, they're going to work. Now we're going to carefully pry it out. You can actually do a couple different ways here. You sort of get it in the screw hole here, you sometimes can get a grip on it, sort of work it out.

You have to lift up from the bottom. Now the switch is out, we're going to remove these two screws. Before we throw our junk bezel away here, remove these two screws and this spring, we're going to transfer this over to the new part. Now, grab our new bezel, and reinstall the spring. To remove the switches, you may need a small flathead screwdriver, but normally you can just kind of get them, give them a little bit of wiggle back and forth and they'll come off.

I'm going to use some canned air while we have it apart, just to clean it up. When you install the switches, there's going to be an alignment tab on each one of them, so you really can't install them the wrong way. Just line that tab up, just press them on.

Now we're going to install the switch assembly onto the new bezel, and reinstall the original screws. With everything installed, now we can reinstall the switch panel, make sure this spring gets underneath this bottom piece here. Get it seated, and install the screw. And then repeat the process on the other side, and your installation's finished.

Our new switch and bezel kit looks great, and best of all, it actually works now. So my doors will open, my windows will open. Like I said, the installation is very, very easy. This should take you no more than about 15 minutes per side, and be back on the road in no time.

Vehicle Fitment

This product will fit the following Mustang years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.