Power Window Switch Cover Passenger Side 1987-1993

CJ's Part Number:


  • Factory Style Replacement
  • Original Details
  • Simple Installation
  • Fits 1987-1993 Mustangs
MSRP $32.99
You save 24%

Passenger Side Power Window Switch Cover for all 1987, 1988, 1989, 1990, 1991, 1992 and 1993 Mustangs.

Replace the faded, worn or broken power window switch bezel in your 1987-1993 Mustang with this factory style replacement. Features the same details as the original switch bezel.

Features and Benefits:
- Factory Style Replacement
- Original Details
- Simple Installation

The bold white text of this power window switch cover will give your Fox Body interior a new look. This factory style replacement cover retains the power window switches on the passenger side door. Replacing the window switch bezel is very simple and only requires the removal of a few screws. This new unit will accept the factory hardware as well.

The window switch bezels take quite a bit of abuse just like the switches. Text usually wears off just like many other interior parts. Keep your interior looking new by replacing your worn parts. When replacing the window switch cover, it is also a good idea to replace any window switches that need replaced. This bezel fits any 1987-1993 Mustang passenger door.

CJ Pony Parts is your one-stop-shop for all things Ford Mustang! No matter what you need for your Mustang, whether it is for the engine, interior, body, etc.—the chances are, we have it!

Purchase a Passenger Side Power Window Switch Cover for your 1987, 1988, 1989, 1990, 1991, 1992 or 1993 Mustang from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

On today's quick fix video, we're going to show you how to replace your power door lock switches as well as your power door lock window switch bezels on your '87 through '93 Fox Body Mustang.

These bezels will fit your '87 through '93 coupe or hatchback equipped with power windows and power locks. A convertible version is available, which will have two additional cutouts for the rear windows located there. They are side specific with two window cutouts on your driver's side and a single on the passenger's side. Your locks are also side specific, with the unlock button on the outside and the lock towards the inside.

For this quick fix, you'll need a Phillips head screwdriver, a 1/4 inch ratchet, and a 1/4 inch socket. We're going to install the passenger side on our '90 GT since we've been having some problems with the door lock button not working properly. Both the driver and passenger side install the same way. See when we hit out button our doors aren't unlocking. We know we replaced the actuators recently, so it's probably going to be the switch. We're going to replace that first.

Not only is our switch bad, you can see there's a crease in our plate as well. This seems to be a common problem with these cars if these aren't installed properly. We're going to start by removing this Phillips head screw. Now we're going to pull out and then lift up, take the clip off the bottom and then pull it all the way out of your door.

The switches are held to this switch plate by these two Phillips head screws. We're going to remove those next. Then we're going to separate the plate from the switches. Removing the old switch is easy. Just grab the sides and pull it straight off. Now we'll slide the new switch on slide it up press it into place and now we can check our door locks. Everything works perfectly. Time to install the cover plate.

The new cover plate comes with a new mounting tab. It does not come with hardware so you have to remove these two screws off the original to install on the new one. Install the new piece. Make sure the edge is facing up when you install it, and we're ready to install.

Install our cover plate over our switches and we'll reinstall the two screws. Then the last step is reinstalling the door panel. Lift the tab in at the bottom, seat it properly and reinstall the screw and your quick fix is finished. There it is: a simple fix to a common problem. If your window switch goes out, the installation is exactly the same. Overall it will take you no more than about five minutes.

Vehicle Fitment

This product will fit the following Mustang years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account
Complete Your Package
Add to Cart