Sequential LED Taillight Kit with Quick Connect Flasher 1996-2004

CJ's Part Number:
95% of 100


  • Sequential Taillights
  • Quick Connect Flasher
  • Detailed Instructions
  • Direct-Fit
MSRP $428.99
You save 14%

Sequential LED Taillight Kit with Quick Connect Flasher for all 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003 and 2004 Mustangs.

This sequential turn signal kit is unique because your brake lights will still work properly. The taillights will only sequence when the turn signal or emergency flasher is activated but the brake lights come full on when braking. You will gain sequencing turn signals but also a much brighter and clearer light with the help of LEDs.

- Fits 1996-2004 Mustangs
- LED Bulbs
- Sequential Taillights
- Quick Connect Flasher
- Detailed Instructions

Please Note: This kit will also work on all 1994-1995 Mustangs equipped with 1996-1998 style tail lights.

No need to change harnesses or cut wires. No permanent modifications are needed. Simply replace your flasher module with the patented electronic module and replace your incandescent lamps with the LED modules.

Do the headlights in your SN95 have moisture in the fixture? Do you want LED taillights? You can add both to your 1994-2004 Mustang, along with many other lighting options from CJ Pony Parts. Take a look at over 100 different part options, and make plans to install new headlights, taillights, fog lights and much more, so you can set your Mustang a part from the crowd, or just get it looking great again.

Purchase a new Sequential LED Taillight Kit with Quick Connect Flasher for all 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003 and 2004 Mustangs from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Related Categories: Mustang Parts, Mustang Lighting, Mustang Taillights, Mustang LED Lighting, Mustang LED Taillights

Installation Videos

Video Transcript

Converting sequential taillights has been so popular in the Mustang crowd, Ford made it a standard feature starting in 2010. If your Mustang's a little bit older than that, there's plenty of aftermarket ways to convert your taillights. Today, we're going to install this LED Sequential Kit in this 1996 Cobra. The kit includes six of these ultra-bright LED bulbs, all the wiring necessary, and a special flasher.

We're going to start by removing this plastic trim panel so we can remove the panel that covers our taillights. Taillight are held in by four nuts. There's going to be one here, here, up top, and the other one's going to be back here behind this plastic bracket. We're going to pull the taillight out. It's not a bad idea to put a blanket or towel of some sort down to protect your paint. We're going to start by removing the outermost plug-in socket. Simply turn, slide it out, remove the bulb.

Now you want to grab the LED assembly that's marked outer. We're going to plug it into the original plug and install it in the housing. Now we're going to remove the middle one and take the bulb out of that, then finally the inner and remove the bulb from that one there.

We'll install our new LED harness and bulbs. You want to make sure when you install these that the bulb labeled "I" is on the inside. You then take this harness and you're going to plug it into the middle light socket. The factory light socket on the innermost inside does not get used. Now you want to install your new flasher. Once we unplug the original, we'll plug the new one in. We'll tie this up out of the way.

Once you've installed the flasher, you'll want to check your lights. In a case like ours, when you only have one bulb on, that means the polarity on the middle plug is reversed and you want to flip it over. Simply pull the plug out, flip it over, plug it back in. Now that the lights are working properly, we're ready to reinstall our taillights and reassemble our trunk.

Now there's some extra sockets in the car. You want to make sure you push them towards the top where there's more room before you try to reinstall. I'll reinstall the retaining nuts. I'll reinstall the trim panel and reinstallation's completed. Not only do we get that classic sequential look, the LED's going to be a lot brighter, making this a safety upgrade as well. The only real tool needed for installation is going to be an 11-millimeter socket. If you choose to remove the rear panel, you'll need a panel removal tool as well. Installation should take you no more than half an hour, so you'll be back on the road in no time.

Vehicle Fitment

This product will fit the following Mustang years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account