Classic Design Concepts Sequential Taillight Kit for all 2005, 2006, 2007, 2008 and 2009 Mustangs.Sequential taillights are a perfect complement to the attractive retro styling of the 2005-2009 Mustang. When you install this Classic Design Concepts Sequential Taillight Kit for all 2005, 2006, 2007, 2008 and 2009 Mustangs and step back to take it all in, you’ll see a beautiful combination of old and new styling that is sure to please. When the brake is applied, the lights will sequence once from inboard to outboard, then remain illuminated until the brake pedal is released. This is a unique effect that is just one more of the countless ways to make your pony stand apart from the herd!
This advanced engineered system uses brand new harnesses and sockets with a pre-programmed microprocessor that controls the timing for an optimum and safe performance. This Classic Design Concepts Sequential Taillight Kit for all 2005-2009 Mustangs has been moisture tested and cycle tested for high quality results. When you order this kit from CJ Pony Parts you know you are getting a great product at a fantastic price, so get yours today and start impressing your friends and competitors alike with this brilliant new taillight display!
This kit comes complete with simple "Plug and Play" instructions for wiring and installation that requires no splicing or complicated hook-ups, simply unhook the wiring from your stock taillights and plug these right in their place. Order your Classic Design Concepts Sequential Taillight Kit for all 2005-2009 Mustangs today from CJ Pony Parts and you’ll see how extremely easy it is to install and enjoy the use of solid state electronics for a long-lasting reliability.
Product ReviewsWrite a review
problem with sequential light left side. already tried to reset by unhooking negative post on battery. The right side works OK, but the the left side does not sequence. bulb #1& #2 come on at the same time the bulb #3 it does not go 1,2,3 sequence.
Does this product include both left and right tailights?
sequential 129.99 iz american money on canadian money
the Classic Design Concepts Taillight Kit Sequential 2005-2009 is $129.99 américan money on canadian money
What is the difference between this kit and the Scott Drake kit? Scott Drake one being Programmable?? I am probably only looking at one sequence mode but not sure the preference or if which mode of the Scott Drake one equals this version.
Under Product Question portion there is a conflicting Q/A. the question, can you use LED with this sequential harness, one cj Pony rep said yes adsax, another cj Pony rep jettabor said no a different harness is required. Would you clear this up thanks
Can led lamps be used with this harness?
I am having problems with my 2006 Mustang with OEM sequential tail lights not functioning correctly. Can I use this wire harness to replace the factory sequential harness?
You Might Also Like
Regular Price: $150.97
Special Price: $143.42
CJ's Low Price:$149.99
For this installation, we need a quarter inch ratchet, 11 mm deep socket and a small pick. The installation requires us to pull the taillight bodies off the car. The first step is to remove these plastic trim panels from inside the trunk. Start by unthreading this one here. To pop these clips out, we need a small pick. Pull up and put the panel aside. Now, you want to disconnect the taillight harness by pushing down on the clip and simply sliding it upward. Now were going to remove the three retaining nuts holding the taillight to the body. I'm going to push the harness through down here. I'm going to carefully push against the studs of the taillights to remove our taillight.
Once you have the taillight removed, you want to remove the original harness by turning the sockets and pulling them outward. Now we're going to remove our bulbs so we can put them into the new harness. The bulbs will just press into place, and now we're ready to install the harness back in the housing.
The sockets are numbered; you want to make sure you have one on the inside and three on the outside. Now we're ready to reinstall it back on our car. You reinstall the same way you took it out. Fish the harness through first. You want to make sure you get the harness pushed through and seated before you put the taillight up into place. Now were going to reinstall the retaining nuts. Make them snug, you don't want to crank too tight on them. Once you bolt the taillight back in, make sure the harness is seated properly here in the grommet and plug it back in.
Once everything is installed and wired up again, we're going to want to test our lights. Once everything's good, you're going to want to put your trunk back together, and your installation is complete. Our Sequential Taillight Kit looks great on the back of our '06 Mustang and installation couldn't be easier. Figure on no more than 30 minutes; you'll be back on the road in no time.