Full Length Floor Pan for 1965-1970 Mustang Coupes and Fastbacks.These heavy gauge stamped steel floor pans start at the front of the rear seat and extend all the way to the base of the firewall. Save time and money with these full length floor pans. Will fit 1971-1973 Mustang Coupes and Fastbacks but the ribbing is styled after 1965-1970 Mustangs.
Product ReviewsWrite a review
Floor Pan Full Length Coupe/Fastback 1965-1970 is rated out of 5 by 7.
Rated 3 out of 5 by Nfrutiger7 from cheaper quality As I said cheaper quality not a good match to original pans ended up with to different pans as you can see in the photo also not perfect fit but if your just doing the bad you can fit it well to the bottom for the money it's not to bad
Date published: 2015-01-08
Rated 5 out of 5 by TooTatted from A Product for ALL Mustangs! This is one of two different floor pans that I purchased from CJ Pony Parts. I wanted to compare quality of the two and I must admit that they were both of amazing quality. Both products are made of a thick steel that is also pliable so that you can make it fit perfect to your specific 1965-1970 Mustang. I found that there was very little I had to do to make this floor pan fit perfectly in my classic pony. This is a product that I believe is worthy to be in any and all coupes and fastbacks, whether your Mustang is a daily driver or a show car.
Date published: 2015-01-17
Rated 4 out of 5 by Mike68 from Easy to work with I received both this LH floor panel and a RH one too. This one was exactly as pictured and the installation was relatively simple. The lighter gauge steel helped with doing some custom molding around the floor board area. The weld through primer is excellent in both protection and ability to weld. Pay attention to the edges and make sure you do not remove too much of the old. This panel was different than the RH and I took too much old out based on the other side.
Date published: 2015-01-10
Rated 5 out of 5 by woppybalboa from Good deal!! I bought the "kit" whitch has both drivers and passenger side. By getting the "kit" I was able to save a few more bucks plus free shipping, and 128 points. So basically $5 off my next purchase. You can't go wrong. Decent fit considering they're going on a pretty rough car that is 35 years old, by amateurs.
Date published: 2015-01-07
Rated 5 out of 5 by Dreaming Dad from Worked well Purchased to start rebuilt with my 15 year old son. Cut out old and welded in new easily. Moving to the next section.
Date published: 2015-01-07
Rated 5 out of 5 by dantheman from extremely happy First I love free shipping. Parts arrived in 3 days!! Floor pans very high quality and I am so happy with the fit
Date published: 2015-01-28
Rated 5 out of 5 by mad mustang man from floor pans good fit with very little trimming. price was exellent
Date published: 2015-01-09
do i need to sand off the black primer so i can paint it with a good undercoat paint or is this primer a good base?
It'll accept the undercoating without any sanding.
Date published: 2015-08-03
how long take the free standar ground shipping
It varies depending on location and stock status of the product.
Date published: 2015-07-22
My 67 floor pans are gone but my seat pans are solid. Do you have a kit that comes with the front & back pans but not the seat area? Or should I just replace the seat pans to? do they have holes for the seats? I'm using 3m panel bond to install them
We may have the front and rear sections only. Browse our floor pan category to see what we have and make sure that it works for your install, but M106L, M106R, M108L and M108R are some CJ part numbers you might want to check out. http://www.cjponyparts.com/mustang-floor-pans/c/60020100/
Date published: 2015-06-20
HOW MUCH DOES ONE PANEL WEIGHT?
A left or right panel weighs approximately 15.5 pounds.
Date published: 2015-04-16
Hello, I have a question. Do you know if this floor pans fits on 4-door Thunderbird from 1967? I think that dimension can be the same, but not sure. And is there chance that roof panel can be little similar?Sorry for my english and thank you for answer.
Unsure. We've only tested those parts for the fitments listed, so anything outside of that is untested, meaning it could work, but it might not.
Date published: 2015-03-06
What gauge metal are your floor pans stamped in?
Hi . I want to know if the floor pan of a 1967 mustang fit a 1967 ford falcon .. thank you.
You Might Also Like
CJ's Low Price:$2,547.99