Diode Dynamics Sequencer Tail Light Kit 2010-2020

Diode Dynamics:
DD3016
Rating:
96% of 100

Highlights

  • Made In The USA
  • Plug And Play Kit
  • Easy Installation
  • Adds Sequential Function
MSRP $80.00
$79.95
You save $0.05

Diode Dynamics Tail Light Sequencer Kit for all 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019 and 2020 Mustangs.

In 2010, Ford introduced and included sequential turn signals on all Mustangs, and since then they have maintained the trend all the way up to the current model. Unfortunately the sequential pattern is only used for the turn signals, not anymore!

With this Diode Dynamics Sequencer Kit, the brake and hazards lights will not flash with a static pattern. This easy to install kit will make the tail lights flash in a sequential pattern for all of your typical functions - including brake, hazard, and locking/unlocking your 2010-2020 Mustang. This plug and play sequencer kit will take only minutes to install, and requires no permanent modifications to your factory wiring harness.

Diode Dynamics Tail Light Sequencer Kit DD3016 Features and Benefits:
- Adds Sequential Abilities to all Lighting Functions
- Fits all 2010-2019 Mustangs
- Requires no Permanent Modifications
- Complete Plug-and-Play Kit
- Made in the USA
- Quick and Easy Installation
- 100% Reversible
- Sold as a Pair

*Please confirm that you have US-Spec Sequential Tail Lights prior to placing your order.

Please Note: This Tail Light Sequencer Kit will only work on US-Spec Tail Lights and may NOT be compatible with aftermarket tail lights and/or aftermarket bulbs.

The kit from Diode Dynamics has been engineered with only the highest of quality parts, including modified OE-grade connectors featuring an embedded circuit protector for extreme reliability over the life of your Mustang. Designed, tested, and manufactured right here in the USA and offering a fully plug-and-play installation, this is by far one of the simplest ways to make your 2010-2018 Mustang stand out from the rest.

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

If you subscribe to our YouTube channel, you know we do a lot of videos showing you how to add sequential tail lights to both old and new Mustangs. Starting in 2010, Ford made sequentials a factory feature, so now instead of installing them, we're showing you ways to make them better. These harnesses will fit your 2010-2016 Mustang, and kind of take your sequential tail lights to a new level. Instead of simply sequencing when your turn signals are on, now they'll sequence when you unlock the car, when you hit your brakes, and also when the hazards are on, and given that the first factory Mustang with sequential tail lights was a Shelby, it's only fitting that they're going to fit the new Shelby’s as well.

Today we're going to install a set on this 2016 GT-350.

These sequencing were made in the USA and are a very easy installation on all 2010 through 2016 Mustangs. You simply have to unplug the factory harness from the tail light and put this in line with it, and plug it back in. Very simple to do, and we'll show you how to do it on the new Shelby.

I'm going to start the installation by popping the trunk, and we're going to remove the cover for the installation device.

Next we're going to remove this rear panel by removing these 4 thumb screws. There are going to be 2 on each side.

Okay next, the panel, you're going to kind of pull it forward towards the front of the car and kind of lift up.

I should mention at this point, if you do have a factory subwoofer in your car, you are going to have to remove the subwoofer to install this part. It's only a few bolts. It's very easy to remove, but get that out of the way. We're going to actually tilt this forward, and you can see the plug.

Now we'll reach down and plug it from the top. Take the sequencer. They're both the same. Install that, and plug it back in the factory harness.

Now repeat the process on the other side.

With both sides plugged in, we give them a quick test. The easiest way to do this, you can hit the hazards, hit the brakes, or just hit unlock on key fob. Okay, now they sequence just like the turn signals do when I'm unlocking the car. Now we can reinstall the panels that we removed, and your installation is finished.

Here you see the tail light sequencers with the brake lights on. Once you hit the brake light, all of them will stay on, and when you release they go off. Hit it again, and they sequence, and here's the hazards.

Here you can see the turn signals work just like factory.

The tail light sequencers add a nice custom touch to our Shelby. Obviously it's great that they sequence when the tail lights and turn signals are on, and now you get them with your brake lights, your hazard lights, even when you disarm the car.

Installation is very straightforward, very easy. Even with subwoofer, it should take you no more than 30 to 45 minutes, and be back on the road in no time.

Vehicle Fitment

This product will fit the following Mustang years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.