Powermaster Starter XS Torque Mini Chrome For 164 Tooth Flywheel 3-Speed/4-Speed 302/351W

MSRP $407.50
You save 22%

Powermaster Chrome XS Torque Mini Starter for 302 or 351W Engines with a 3-Speed or 4-Speed Transmission and a164 Tooth Flywheel.

Does your 302 or 351W not want to start due to a bad starter? Replace your damaged or worn out factory starter with this high Performance starter from Powermaster. This XS Torque Mini Starter (19504) features a 3/4" offset for proper mounting alignment. Offset is the distance from the mounting surface of the starter to the engine side of the ring gear.

Powermaster's highly efficient XS Torque starters feature extra-powerful motors that churn out up to 200 ft.-lbs. of torque. Coupled with their 4.4:1 gear-reduction ratio, that adds up to reliable cranking power for engines up to a whopping 18.0:1 compression ratio. These starters come with a billet adapter/mounting block and will clear all headers. They'll also clear your oil pan if the OE starter did. Starter dyno test results are included.

- Chrome Housing
- 4.4:1 Gear Reduction
- Recommended for 18:1 Compression
- Machined Aluminum Adapter Block
- Adds extra Clearance
- Weighs 8.5 lbs.
- Fits 1969-1973 302/351 Mustangs with a 3-Speed or 4-Speed Manual Transmission

Please Note: This Powermaster starter is designed for a 164 Tooth Flywheel.

Please Note: This starter will work for Broncos and F-100s that have a small block V8 and 164 tooth flywheel with an automatic transmission.

*Small block engines refers to 302 / 351W.

Powermaster Performance offers high performance Starters for early model Ford Mustangs. Powermaster has a wide range of choices to fit just about any application. Check out CJ Pony Parts large selection of starters from Powermaster and get your Mustang back on the road in no time.

Order your new Powermaster (19504) Chrome XS Torque Mini Starter for 302 or 351W Engines with a 3-Speed or 4-Speed Transmission and a164 Tooth Flywheel from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Related Categories: Mustang Parts, Mustang Engine, Mustang Starters & Starter Solenoids, Ford Bronco Parts, Ford F-100 Parts

Installation Videos

Video Transcript

The starter is one of those pieces you never really think about upgrading until it fails on you. In this case, for our '67 convertible, we're planning on a T5 swap as well as a few other upgrades, so now's a perfect time to upgrade to a high- performance starter from Power Master.

Power Master is serious about the performance of the XS torque starters, so much so that every one of their starters comes with one of these dyno sheets showing you actual performance the starter put out. They also use the smallest chassis possible and their Infi-clock system allows turning in the mounting bracket, making it much easier to install in your Mustang.

The XS torque starter's going to come with two terminals mounted on it. If you're installing one of these in your early Mustang like we are, you'll want a jumper between these two since you're using a single wire with an external starter solanoid for your classic Mustang.

For this installation you'll need a jack and jack stands or lift, 3/8th ratchet, 12-inch extension, 9/16th socket, 1/4-inch ratchet, 9/32nd socket, crimping tool, wire strippers and safety glasses. The bottom bolt is pretty easy to get to; the top one we're going to have to use an extension or a swivel of some sort. The header is going to make it a little bit harder; you should be able to get it off though.

You've got to remove the wire. Since our early Mustang has an external starter solanoid, you'll want to make a jumper to go between the two terminals on the starter. You connect the starter to the starter wire before you put it up in to place. You'll want to get this connection snug; you don't want to overtighten it. Now I can put our starter up in to place.

Once our starter is bolted and the wires are connected, we're ready to test it! Our Power Master starter had no problems with our stock 289 and is strong enough for any motor we put in, in the future. Installation, figure 45 minutes to an hour. You'll be back on the road in no time.

Vehicle Fitment

This product will fit the following Bronco years:

This product will fit the following F-100 years:

This product will fit the following Mustang years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account