Two Terminal LED Flasher for 1965-1969 Mustangs.This is required when using LED parking lights (PLLED1) and LED taillights (TLLED12, TLLED13 or TLLED14). When using LEDs, your stock flasher mechanism cannot engage properly, due to less heat given off from the LEDs than original bulbs. The two terminal flasher allows your flashers/turn signals to work properly when using LED style lights. Car requires one.
Product ReviewsWrite a review
Led Flasher Two Terminal 1965-1969 is rated out of 5 by 10.
Rated 1 out of 5 by boneyfinger from Did not work! I purchased this flasher when I installed LED Tail Lights and Front Turn Signal Lights in my 67 Mustang. With the ignition on (engine not running) everything worked fine. When I started the car, the turn signals would not work correctly. They would flash, stop flashing, stay on, turn off, etc. Thinking I might have a bad flasher, I ordered a new one and had the same results. Thinking it might be the ground, I ran the ground wire to two different locations with the same results. As a last resort I went to AutoZone and purchased an light duty flasher. Installed this new flasher and everything works perfect. I might add that this car has a new AAW wiring system.
Date published: 2015-09-02
Rated 5 out of 5 by Kwin from Nice! This product is quality and very useful! It's fairly easy to install if you know where to look!(upper left hand of your dash the original one is brass And is mounted on the back of your driver side air vent) this product saved me!
Date published: 2015-01-08
Rated 5 out of 5 by Richmac from Led flasher Easy to install and works well in conjunction with the LED taillights I purchased. I wish the ground wire was a little longer though, it was a little more difficult to find a good place to ground it.
Date published: 2015-07-21
Rated 4 out of 5 by DAKIBBS from Works great, thanks I bought this to add LED brake lights to my 1966 Mustang, It was very easy to hook up.
Date published: 2015-08-08
Rated 1 out of 5 by bowler300 from Did not work I purchased this flasher to go with the LED front turn signals that I bought before from CJ. I already had LED on the back and they work great. When I installed the LED on the front they would not work. Both would flash at the same time. So am back to the original bulbs in the front.
Date published: 2015-12-27
Rated 5 out of 5 by coachwoz from great flasher I had bought new tail lights but did not realize you needed a new type flasher. just thought it was a direct plug in ready to go. Found out I needed LED flasher . Ordered. works great and easy to install
Date published: 2016-01-28
Rated 5 out of 5 by Adrien78 from Work great Very easy to install, just connect the black wire to ground. Be careful of the wiring, it was the oposite of the original flasher for my 66.
Date published: 2016-01-19
Rated 5 out of 5 by chuckm60090 from Easily replaces the old flasher Need to find a good ground for the external wire but that's not a problem. Plenty of mounting places under and around the dash.
Date published: 2015-06-19
I just switched over to the LED tail lights on my 1966 mustang Fastback. Which flasher module do I need? Thanks Jeff
This one is exactly what you need.
Date published: 2015-08-21
I am looking at the the part number HW2811, which is a LED Flasher for my 1968 Mustang Convertible. Will this flasher work if there is a mix of incandescent and LED bulbs? My goal is to replace the tail lights first and slowly buying other LED's I need.
Yes, it will work fine with a mix of bulbs.
Date published: 2015-06-29
I have installed front and rear LED lights, PLLED1 and TLLED12, along with the HW2811 flasher. Everything works like it's supposed to with the exception of the front turn signals, with both flashing when turning left OR right. Bad flasher? Any ideas?
My first check would be to make sure all of the wiring is connected properly and that you have an excellent ground. If everything's good there and all of the lights are working properly otherwise, then, yes, I'd agree that the flasher might be bad.
Date published: 2015-06-24
Why won't this work on a 1970 mustang ?
Wiring differences cause incompatibility.
Date published: 2015-06-01
Can i mix orginal bulbs and leds with this flasher ?
You could - you might not install LED taillights at the same time as your parking lots (or vice versa), and since the car only requires one of flasher modules, all bulbs (LED and non-LED) would work fine.
Date published: 2015-05-11
Is one sufficient for both turn signals & emergency flashers, or are two needed (one for turn signals & another for emergency flashers)? Thanks
A respectful correction to Fins2Ryt: You will need 2 of these flashers if you change your taillights and front blinkers over to LED lights - one to replace your normal turn signal flasher (located behind left side footwell airduct) and another to replace your emergency flasher (located within a few inches of your emergency flasher switch)
Date published: 2015-04-09
Is this the correct flasher to be used with the TLLED68 and if not, which one is? Thank you
Yes, it is.
Date published: 2015-03-19
so i was wondering about the wire leading off of this part is that a neutral or is it something else because from what ive seen on mine it doesnt have that
From the wiring diagram, I'm thinking that's the ground.
Date published: 2015-01-16