Holley HyperSpark 2 Ignition Box Sniper EFI
Highlights
- Plug-And-Play Installation
- Max Spark Energy And Output
- Quicker Throttle Response
- Made In The USA
Holley HyperSpark 2 Snipe EFI Ignition Box.
The Holley HyperSpark 2 Snipe EFI Ignition Box (556-154) provides your ride with an upgraded ignition system that is both easy to install and full of features for optimal performance. Proprietary features and innovative technologies allow for the use of high-energy, multiple sparks across a wide rpm range with less current draw to ensure complete combustion. This ignition box is protected against common shortage issues and is 1.47 lbs. lighter than the original HyperSpark ignition box. Enjoy a quicker throttle response and start with this improved ignition box.
Features and Benefits:
- Plug-and-play with existing HyperSpark installations
- Compatible with Sniper EFI HyperSpark main harnesses
- Includes an ignition harness for fresh Sniper EFI Installs simply wanting to add timing control
- New processor and board design provide a highly efficient ignition
- Minimal heat and max spark energy and output with less current draw
- HyperSpark ignition coil (COIL32) provides High RPM operation
- Consistent 135mJ to 150mJ high spark energy every firing (idle to redline rpm)
- Operates on most 7 to 28-volt electrical systems
- Fully protected against an open coil, shorted coil, and open load
- 1.47 lbs. lighter than an original HyperSpark ignition box
- Quickens throttle response and improves starting
- Tach output to drive an external tachometer
- Made in the USA
Not only does this product make installation simpler with its plug-and-play abilities, but an additional ignition harness for fresh Sniper EFI installs is also included if added timing control is needed. For maximum output and power at idle to redline rpm levels, the Holley HyperSpark 2 Snipe EFI Ignition Box has you covered!
Vehicle Fitment:
- 1965-1985 Mustangs
- 1948-1979 F-100s
- 1966-1977 Broncos
- 1960-1987 C10s
California Residents: Proposition 65 Warning
Related Categories: Mustang Parts, Mustang Engine, Mustang Ignition System, Mustang Ignition Boxes, Ford Bronco Parts
Only for use on pre-pollution controlled vehicles: This product can be used on vehicles that were manufactured before emissions control regulations were imposed. Pre-pollution vehicles are defined as:
- 1965 and older U.S. manufactured California certified vehicles
- 1967 and older U.S. manufactured federally certified vehicles
Vehicle Fitment
This product will fit the following Bronco years:
This product will fit the following C10 years:
- 1960,
- 1961,
- 1962,
- 1963,
- 1964,
- 1965,
- 1966,
- 1967,
- 1968,
- 1969,
- 1970,
- 1971,
- 1972,
- 1973,
- 1974,
- 1975,
- 1976,
- 1977,
- 1978,
- 1979,
- 1980,
- 1981,
- 1982,
- 1983,
- 1984,
- 1985,
- 1986,
- 1987,
This product will fit the following F-100 years:
- 1948,
- 1949,
- 1950,
- 1951,
- 1952,
- 1953,
- 1954,
- 1955,
- 1956,
- 1957,
- 1958,
- 1959,
- 1960,
- 1961,
- 1962,
- 1963,
- 1964,
- 1965,
- 1966,
- 1967,
- 1968,
- 1969,
- 1970,
- 1971,
- 1972,
- 1973,
- 1974,
- 1975,
- 1976,
- 1977,
- 1978,
- 1979,
This product will fit the following Mustang years:
