Powermaster Starter Powermax Chrome For 157 Tooth Flywheel/Flexplate 3-Speed/4-Speed/5-Speed/Automatic 289/302/351W
Highlights
- For 157 Tooth Flywheel
- 4.4:1 Gear-Reduction
- Direct-Fit Replacement
- Quality Replacement
Powermaster Chrome Powermax Starter for 289, 302 or 351W Engines with an Automatic Transmission or a 3-Speed, 4-Speed or 5-Speed Manual Transmission and a 157 Tooth Flywheel or Flexplate.
Does your 289, 302 or 351W Engine not wanting to start due to a bad starter? Replace your damaged or worn out factory starter with this High-Performance Starter (19162) from Powermaster. This Powermax starter features a 3/4" offset for proper mounting alignment. Offset is the distance from the mounting surface of the starter to the engine side of the ring gear. Includes wiring kit. Weighs only 8.5 lbs.
Applications:
- 1965-1968 289/302/351W Mustangs with a 3-Speed or 4-Speed Manual Transmission
- 1965-1973 All Mustangs with an Automatic Transmission or 5-Speed Manual Transmission
- 1966-1977 Small Block V8 Broncos with an Automatic Transmission
- 1970-1979 Small Block V8 F-100s with an Automatic Transmission
This starter is a great choice for daily drivers with a stock compression ratio and timing. Powermaster's highly efficient Powermax starters feature extra-powerful motors that churn out up to 160 ft.-lbs. of torque. Couple that with their 4.4:1 gear-reduction ratio and you get reliable cranking power for engines up to a 10.5:1 compression ratio. Starter dyno test results are included.
Powermaster Performance offers high-performance Starters and Alternators for early and late model Ford Mustangs. Powermaster has a wide range of choices to fit just about any application. Check out CJ Pony Parts large selection of starters from Powermaster and get your Mustang back on the road in no time.
Purchase your Powermaster (19162) Chrome Powermax Starter for 289, 302 or 351W Engines with an Automatic Transmission or a 3-Speed, 4-Speed or 5-Speed Manual Transmission and a 157 Tooth Flywheel or Flexplate from CJ Pony Parts!
California Residents: Proposition 65 Warning
Related Categories: Mustang Parts, Mustang Engine, Mustang Starters & Starter Solenoids, Ford Bronco Parts, Ford F-100 Parts
Installation Videos
Video Transcript
Brady: Thanks for having me, Bill.
Bill: What can you tell me about Powermaster?
Brady: Well, Powermaster Performance was started in 1981 making some OE parts. We do work for Richard Petty Driving School, Grave Digger monster trucks. In 1992, the Powermaster brand was started. What we do is high performance starters and alternators. We have a one-year warranty on our products and 90 days on some of the race stuff. We do a full refurb program for anybody that runs into a little trouble with an install or damages some products on a race vehicle.
We have everything from stock replacement alternators and starters all the way up to high performance gear reduction for engines up to 18 to one compression, alternators up to 200 and higher amperage. Basically anything for the street, strip and hot rod type applications.
Bill: Where are your products made at?
Brady: Everything we do is made in our 150,000-square foot plant in West Chicago, Illinois. We've been there since 1981 and we're not going anywhere.
Bill: I'm familiar with your starters and alternators, but I wasn't aware you guys made a generator.
Brady: Well, Bill, we actually don't. This is an alternator that just looks like a generator. This is for guys that are looking for a little bit higher amperage than the factory piece. We dyno test every starter and alternator that leaves the plant. Every alternator gets our proof of performance tag.
As you can see, this one did 90 amps at the top end, 72 at idle, which is well over three times the output a factory generator would've done. That's in half the weight of a factory generator package.
Bill: What can you tell me about this generator you brought with you?
Brady: What we brought with us today was the 200-amp in a natural finish here for upgrade on later model vehicles. We got a hundred amp one wire for a serpentine setup in a black finish. We also brought a chrome finish for the earlier models with the v-belt on it. That's again a one wire hundred amp hookup. Those come with the mounting hardware so that they'll bolt right into your Mustang. We offer anything from a stock replacement 60-amp externally regulated all the way up to that 200-amp of direct replacement.
Bill: They're all available in three finishes?
Brady: All available in not just these three finishes, but we also offer polished and a brand new satin finish that we're working on now.
Bill: Brady, I know starters are a big part of your business at Powermaster. Want can you tell us about this one you brought with you today?
Brady: This is our XS torque 200-foot pound starter. It's got a fully aluminum-encased solenoid and armature housing. What that does it helps keep heat soak down. The heat's going to dissipate right out of the starter motor during cranking. What it also has is our fully-adjustable intra-clock style feature. This starter can be rotated 360 degrees to clear headers and kick out an oil pan or really any obstacle you may have in the way, all in a package that will turn an engine up to 18 to one compression with no problems.
Bill: The Powermaster has taken a part that most people view as a replacement item and made it into a true performance necessity.
Brady: That's right. We've been making starters and alternators for your Mustang for over thirty years right here in the U.S.
Vehicle Fitment
This product will fit the following Bronco years:
This product will fit the following F-100 years:
This product will fit the following Mustang years: