Eastwood Self Etching Weld Thru Primer 16.1Oz. Aerosol Can

Eastwood: 12899 Z
CJ's Low Price:
$16.99
1469836800 12854
Earn 16 RPM Points What's this?
Eastwood Self Etching Weld Thru Primer 16.1Oz. Aerosol Can
Eastwood

Product Description

Eastwood 16.1 Ounce Aerosol Can of Self Etching Weld Thru Primer.

Eastwood's Self Etching Weld Thru Primer combines the benefits of a weld-thru and the capabilities of a traditional Self Etch Primer. This unique formula has organic binders that replace conductive heavy metals such as copper and zinc. These organic binders will burn off during the welding process leaving a corrosion resistant etching primer.

This product will reduce spatter and distortion caused by excessive heat that occurs during the welding process. Compatible with MIG, TIG and Arc welding. The etching primer will enhance adhesion and durability and is compatible with most top coats.

*Apply 2 medium wet coats, allowing 5 minutes flash time between coats.
*Allow to cure at least 20 minutes prior to welding.

Product Reviews

Write a review
Eastwood Self Etching Weld Thru Primer 16.1Oz. Aerosol Can is rated 3.6 out of 5 by 15.
Rated 4 out of 5 by from Does the job It seemed to work as claimed. Had no welding issues. Only burned off at the welded areas and did not burn too far back. My only complaint was that the paint would spit as I was spraying larger areas. I don't know if the spray nozzle is not designed correctly as paint would build up on the nozzle and then eventually get into the spray stream which was the cause of the spitting. Not a big deal as the paint will get a topcoat, but this needs to be addressed or looked into. So it gets 4 out of 5 stars due to this.
Date published: 2015-11-28
Rated 3 out of 5 by from Better than nothing Great for getting in areas that get sealed up/overlapped and cant get top coated. It does add to the resistance of the weld, so you'll need a little more voltage. comes right off when you wire brush the slag afterwards though... Also, "self etching" paint is said to conflict with magnetic paints, like Monstaliner. so dont use this if you plan to use magnetic paints....
Date published: 2014-11-10
Rated 5 out of 5 by from great product I have used other Eastwood products with great success and decided to try this one. This paint is great! I have used the weld-thru primer for the backside of patches prior to welding and was very pleased with the results. I would like to see Eastwood make smaller sized spray cans to get into hard to reach places.
Date published: 2015-03-03
Rated 4 out of 5 by from Weld-Thru Works I purchased Weld-Thru just to give it a try. Sprays on nice and smooth, dries fast and covers well. Great for plug welding two panels together. I tried it first by cleaning off the primer just in the area of the plugs on a test piece, then without removing any primer. Works good ether way. Good product..
Date published: 2016-06-04
Rated 1 out of 5 by from Lids popped off - 4 Qts gone I bought 4 quarts and it was in the car in the box. Had to go to work for a few months and when I got back to prime and to weld the roof skin and floors in - the lids had popped off or loose and all dried up. Didn't even get to try it. I want my money back - I'll ship the cans back.
Date published: 2015-02-27
Rated 1 out of 5 by from I want my money back! Like others have said. Horrible as a weld thru primer. Takes away the ground path for the welder. CAUSES SPATTER. is good for stuff u can't access later, but u might as well save some money and use a normal primer and just remove where u r going to weld
Date published: 2015-01-02
Rated 4 out of 5 by from good product Goes on nice and does a good job, the only reason I did not rate 5 was a had to replace the spray tip to eliminate the splatter. I believe the wide spray pattern on the original tip is to wide. Replaced with small one hole tip and went on good.
Date published: 2016-01-16
Rated 5 out of 5 by from Eastwood Self Etching Primer bought this last month, came in with no problems, everything I have bought has been packaged for shipping very well, primer sprays and was able too weld though with no problems.
Date published: 2015-01-18
  • 2016-07-30T07:47CST
  • bvseo_cps, prod_bvrr, vn_cps_3.3.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_15
  • loc_en_US, sid_EW12899Z, PRD, sort_relevancy
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.1.0
  • CLOUD, getContent, 153.21ms
  • REVIEWS, PRODUCT

Product Questions

will this work with electrical connections?

Asked by: leob
It's not really meant to be in contact with electrical connectors. Mask that area off.
Answered by: CJ Pony Parts
Date published: 2015-02-13
  • 2016-07-30T07:58CST
  • bvseo_cps, prod_bvqa, vn_cps_3.3.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_1
  • loc_en_US, sid_EW12899Z, PRD, sort_recentAnswersFirst
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.1.0
  • CLOUD, getContent, 136.6ms
  • QUESTIONS, PRODUCT

You Might Also Like