Dynamat Dynapad Kit
- Stops Excessive Vibration
- Reduces Road Noise
- Easy Installation
- Aluminum Backed Butyl Layer
Dynamat DynaPad Kit.
DynaPad is a heavy-duty four-layer composite barrier providing maximum acoustical attenuation and excellent thermal insulation. DynaPad utilizes "Dissimilar Layer Insulating" technology that solves two of the most difficult automotive problems; exhaust system heat and low frequency noise.
Easy to install, DynaPad can be used in place of carpet pad and is oil and water resistant. Use DynaPad on floors, interior firewalls, rear decks and in trunks for cool, quiet comfort. For optimal results, apply DynaPad over Dynamat Xtreme.
DynaPad Kit Includes:
- One 3/8" thick 32"x54" DynaPad sheet
*Installing DynaPad requires only a few tools such as a razor knife or scissors, roller tool, rags and a solvent-based cleaner (rubbing alcohol also works).
*To complete your DynaPad installation and take your sound deadening to the next level check out all of Dynamats great products such as Dynamat Xtreme, Dynaliner, DynaTape and Dynamats professional grade tools.
Some of the mechanical parts in your Ford vehicle will break down over the decades--it's almost a given. You want to replace them with the highest-quality parts you can find, so the new part will last longer and serve your engine better. Here at CJ Pony Parts, we're dedicated to providing you with the best, highest-quality replacement and reproduction parts available. Your classic Pony, vintage F-100 or First Generation Bronco will be back up and running in no time flat. Browse around for all the parts and pieces you need, and place your order with CJ's today!
Don't wait and order this brand-new Dynamat DynaPad Kit (21100) from CJ Pony Parts today!
California Residents: Proposition 65 Warning
Novice skill is required for this installation.
This translates very well to a restoration project where you may want to make a classic car have more of the interior feel of the modern car by keeping the road noise out and keeping the sound in. Dynamat can be installed with any non-visible metal surface inside your vehicle.
Floors are the most common place to use it due to road noise, but it can also be installed in doors, kick panels, even your roof, trunk, or hood to keep sound at a minimum. Installation is very straightforward. The back of the Dynamat is adhesive. You simply cut it, put it into place, use a roller to adhere it, and you're finished.
The Dynamat Xtreme is the most popular Dynamat we offer. It's available in two different ways. You can purchase it as a bulk kit, which includes 36 square feet that you can mount wherever you want to use it. We also carry vehicle-specific kits for the floor, trunk, and doors of your '64 through '73 Mustang.
Dynamat Xtreme is the original and most commonly used Dynamat. Dynatape can be used to tape the seams of your Xtreme when installing in your vehicle. Dynaliner is available in three different thicknesses and mounts on top of the Xtreme for additional installation. Dynapad is an oil and water resistant pad that can be installed on top of the Dynamat to replace your carpet padding. They also offer a hood liner to insulate your hood.
Let's take a closer look at the complete floor kit for your '64 through '73 Mustang. This is our most popular product that we sell from Dynamat. The kit covers all the pieces you need to cover the floor of your vehicle. When you open the packaging up, it gives you detailed instructions showing where individual piece is going to go. Pieces are all cut and formed to fit specific parts of your floor pan.
Let's go take a look at our '67 Mustang and we'll mock up the installation for you. Here's a piece for the rear floor section, two pieces for your door sill, a piece for under your seat, a front floor pan piece, and also a toe board firewall extension as well.
It will cover both sides of the vehicle and is precut for all the shape of the floor. The installation of Dynamat is going to require to remove the interior from your vehicle. It's a good time to replace worn-out carpet, kick panels, or door sills since they have to be removed anyway. Installation should take roughly five to six hours so you'll be back on the road in no time.
This product will fit the following Bronco years:
This product will fit the following C10 years:
This product will fit the following F-100 years:
This product will fit the following Mustang years:
This product will fit the following Mustang Mach-E years: